Transfer in the Alarm Mode | Panasonic KX-HCM250 specification

Operating Instructions

Transfer in the Alarm Mode

The Alarm mode can transfer an image via e-mail or FTP when the alarm trigger is active. To activate the alarm trigger, the External Sensor Input of External I/O must be connected with the external sensors/devices. The Alarm mode can send the e-mail without transferring the image. The Alarm mode uses the Network Camera internal clock. Make sure Date and Time has been configured. Refer to page 62 about Date and Time.

1.Click [Alarm] on Image Transfer window.

a.

b.

c.

d.

e.

f.

72

Image 72

Panasonic KX-HCM250 operating instructions Transfer in the Alarm Mode, Click Alarm on Image Transfer window

Contents

Network Camera Introduction For operation assistance Call Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 107 Technical GuidesIndex 129 Section Main Features Getting to Know Network Camera Multi Client Access Update FirmwareAuthentication External I/O Input/Output System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM 1 pcAC Adaptor 1 pc Flexible Stand 1 pc Setup CD-ROM Camera Feature Locations IndicatorRefer to page 88 for the setup Front View Rear View Bottom View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Wireless Setup To access Network windowTo set up the wireless network parameters Connection and Signal Strength status Set Infrastructure Default or AdHocChannel Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Viewer Clicking Start CapturePrimary Secondary Multi-Camera Screen Setup Setup Administrator Camera SetupGo to Top Name/Time Entered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the number If you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Name/Time CameraName Date Adjustment Time Changed AM/PM or 24HAuto Time Zone Security Administrator Refer to page 65 for details about authentication securityClick Security Administrator on Setup Enable Administrator and General User Authentication windowFor Setup Password Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor Fixed White Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera Enable check box IP Address orURL * 1 or Host Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation High performance for wireless communication Network Camera Mounting Hook for AC adaptor cordThread the AC adaptor cord through the hook before mounting Flexible Stand Mounting Wall Mounting Ceiling Mounting Attach Network Camera to the tripod by using the tripod bolt Tripod Mounting Wall Mounting Tape Customer provided 100 Ceiling Mounting Interfacing to the External I/O Explanation of External I/OPin Function External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available 104 Displayable character set For assistance, please call 105 Maintenance 106 Specifications and Troubleshooting For assistance, please call 107 Network Camera Reset Procedure-Default Settings Default Settings List For assistance, please call 109 110 Items Factory Default Indispensable setting Value Alarm For assistance, please call 111 Timer 112 For Call113 Control Indicator Control 114 Specifications Network Camera Specifications DescriptionOther Specification Description Weight 530 1.17 lb. Only the unit Mm 3.46 inchesExcluding the antenna and protruding objects AC adaptor Input 120 V AC, 60 Hz Troubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window Network window on Transfers older About Network Camera Setup Problem Cause and Remedy UpdateRefer to page 91 for the Update Firmware 120 Firmware has About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Glossary AdHocEncryption WEP Ieee 802.11b 128 Index 129 Operating Instructions TCP/IP For product service When you ship the product