Flexible Stand Mounting | Panasonic KX-HCM250 specs

Operating Instructions

Notes

•Network Camera is intended for indoor use only. Prolonged exposure to direct sunlight or halogen light may damage the CMOS sensor.

•Make sure the Indicator is always in the upper right corner when you mount.

Flexible Stand Mounting

top

top

bottom

bottom

Wall Mounting	Ceiling Mounting
Wall Mounting
top
bottom	top
	bottom

CAUTION

Drive mounting screws into the wall. Be careful to avoid touching any metalwork (metal/wire laths etc.), conduits or electrical cables buried in the wall.

98

Image 98

Panasonic KX-HCM250 operating instructions Flexible Stand Mounting, Wall Mounting Ceiling Mounting

Contents

Network Camera Introduction For operation assistance Call For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 129 Specifications and Troubleshooting 107Technical Guides Section Main Features Getting to Know Network Camera Authentication Multi Client AccessUpdate Firmware External I/O Input/Output System Requirements Authentication-System Security Feature Authentication window AC Adaptor 1 pc Included AccessoriesSetup CD-ROM 1 pc Flexible Stand 1 pc Setup CD-ROM Refer to page 88 for the setup Camera Feature LocationsIndicator Front View Rear View Bottom View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Parameters Table Network Camera Configuration TypeDefault Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To set up the wireless network parameters Wireless SetupTo access Network window Channel Connection and Signal Strength statusSet Infrastructure Default or AdHoc Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/Time Functions of Network Camera Entered. If any operational issues are changed, tryThis option first. Refer to Go to Top Network Instructions for the data fields Enter only the number Host Name When your ISP uses the Dhcp server function which If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Or administrator for the Host name File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 65 for details about authentication security For Setup Password EnableAdministrator and General User Authentication window Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Fixed Indoor Camera SetupInstructions for the data fields White Balance Fixed Having reached the selected end White Balance is also registered in preset programmingSuggested Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation High performance for wireless communication Thread the AC adaptor cord through the hook before mounting Network Camera MountingHook for AC adaptor cord Flexible Stand Mounting Wall Mounting Ceiling Mounting Attach Network Camera to the tripod by using the tripod bolt Tripod Mounting Wall Mounting Tape Customer provided 100 Ceiling Mounting Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Space, , , #, &, %, =, +, ?, , and are not available Ascii and ISO-8859-1 Character TableUnavailable character set 104 Displayable character set For assistance, please call 105 Maintenance 106 Specifications and Troubleshooting For assistance, please call 107 Network Camera Reset Procedure-Default Settings Default Settings List For assistance, please call 109 110 Items Factory Default Indispensable setting Value Alarm For assistance, please call 111 Timer 112 113 ForCall Control Indicator Control 114 Other Specification Description SpecificationsNetwork Camera Specifications Description Excluding the antenna and protruding objects Weight 530 1.17 lb. Only the unitMm 3.46 inches AC adaptor Input 120 V AC, 60 Hz Problem Cause and Remedy TroubleshootingAbout Network Camera Setup For Indicator Control window Network window on Transfers older Refer to page 91 for the Update Firmware 120 About Network Camera Setup Problem Cause and RemedyUpdate Firmware has About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Encryption WEP GlossaryAdHoc Ieee 802.11b 128 Index 129 Operating Instructions TCP/IP For product service When you ship the product