Update Firmware | Panasonic KX-HCM250 instruction

Operating Instructions

3.5.14 Update Firmware

Update Firmware window allows the user to install the latest version of the Network Camera internal operating system. In most cases, this will never be necessary. Changes may be necessary to accommodate new operating systems or new web browsers that are not shown on page 10. In those cases, Update Firmware would be available from the Network Camera Technical Support Site at http://panasonic.co.jp/pcc/en/. Check the current firmware version on Setup Page on page 54.

Notes

•Do not turn off the power during Update Firmware. If the operation of Update Firmware is stopped, refer to page 120.

•Buffered Images are erased when performing Update Firmware.

1.Download the proper firmware from the Network Camera Technical Support Site mentioned above.

2.If Network Camera is accessible from the Internet, temporarily disable access and connect Network Camera to the PC as the following figure. This will eliminate any interruption during the Update Firmware.

Without Ethernet hub, you should use category 5 cross cable.

or

Ethernet hub

Category 5 straight cable

or

Note

Wireless Router

When Network Camera uses the DHCP function, change the Internet connection from DHCP to Static in Network window. Refer to page 58 for the network parameters.

3.Access Setup Page by entering "http://IP Address (or URL):Port No./ config.html" on the web browser and press [Enter].

•When port number is 80 (default), you do not need to enter port number.

[For assistance, please call: 1-800-272-7033]

91

Image 91

Panasonic KX-HCM250 operating instructions Update Firmware

Contents

Network Camera For operation assistance Call Introduction Network Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 107Index 129 Section Getting to Know Network Camera Main Features External I/O Input/Output Multi Client AccessUpdate Firmware Authentication System Requirements Authentication window Authentication-System Security Feature Flexible Stand 1 pc Included AccessoriesSetup CD-ROM 1 pc AC Adaptor 1 pc Setup CD-ROM Front View Camera Feature LocationsIndicator Refer to page 88 for the setup Bottom View Rear View Network Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a Modem How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Type Port No Network Camera Configuration TypeDefault Network Parameters Table Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To access Network window Wireless SetupTo set up the wireless network parameters Set Infrastructure Default or AdHoc Connection and Signal Strength statusChannel Encryption Key window Encryption Password window Wireless Settings Default Key If Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the Internet Top Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Help Motion JpegSingle Camera Multi-Camera ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Secondary ViewerClicking Start Capture Primary Multi-Camera Screen Setup Setup Name/Time AdministratorCamera Setup Go to Top This option first. Refer to Entered. If any operational issues are changed, tryFunctions of Network Camera Go to Top Network Enter only the number Instructions for the data fields Or administrator for the Host name If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Host Name When your ISP uses the Dhcp server function which File size of the image Date Name/TimeCamera Name Time Zone AdjustmentTime Changed AM/PM or 24H Auto Refer to page 65 for details about authentication security Security AdministratorClick Security Administrator on Setup Retype EnableAdministrator and General User Authentication window For Setup Password Security General User Click Security General User on Setup Operating Instructions Top View Image 160 x ResolutionInstructions for the data fields Top Image Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Fixed Camera SetupInstructions for the data fields White Balance Fixed Indoor Tilt Range White Balance is also registered in preset programmingSuggested Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera Camera Name Enable check boxIP Address or URL * 1 or Host External Output Control Click External Output Control on Setup Indicator Control Status Restart Click Cancel to quit. The window returns to SetupClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides High performance for wireless communication Network Camera Installation Hook for AC adaptor cord Network Camera MountingThread the AC adaptor cord through the hook before mounting Wall Mounting Ceiling Mounting Flexible Stand Mounting Tripod Mounting Attach Network Camera to the tripod by using the tripod bolt Tape Customer provided 100 Wall Mounting Ceiling Mounting External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin Function Circuit Diagram Example 104 Ascii and ISO-8859-1 Character TableUnavailable character set Space, , , #, &, %, =, +, ?, , and are not available For assistance, please call 105 Displayable character set 106 Maintenance For assistance, please call 107 Specifications and Troubleshooting Network Camera Reset Procedure-Default Settings For assistance, please call 109 Default Settings List 110 For assistance, please call 111 Items Factory Default Indispensable setting Value Alarm 112 Timer Call For113 114 Control Indicator Control Network Camera Specifications Description SpecificationsOther Specification Description AC adaptor Input 120 V AC, 60 Hz Weight 530 1.17 lb. Only the unitMm 3.46 inches Excluding the antenna and protruding objects About Network Camera Setup TroubleshootingProblem Cause and Remedy For Indicator Control window Transfers older Network window on Firmware has About Network Camera Setup Problem Cause and RemedyUpdate Refer to page 91 for the Update Firmware 120 Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Ieee 802.11b GlossaryAdHoc Encryption WEP 128 129 Index Operating Instructions TCP/IP When you ship the product For product service