Liquid damage | Panasonic KX-TG6821SA, KX-TG6812SA, KX-TG6811SA

Useful Information

Problem

The unit does not emit the specified number of rings.

Cause/solution

RIf the first ring is turned off, the number of rings decreases by 1 from the specified number of rings.

Liquid damage

Problem

Liquid or other form of moisture has entered the handset/base unit.

Caution:

Cause/solution

RDisconnect the AC adaptor and telephone line cord from the base unit. Remove the batteries from the handset and leave to dry for at least 3 days. After the handset/base unit are completely dry, reconnect the AC adaptor and telephone line cord. Insert the batteries and charge fully before use. If the unit does not work properly, contact an authorised service centre.

RTo avoid permanent damage, do not use a microwave oven to speed up the drying process.

Registering a handset to the base unit

1Handset:

MN#130

2Base unit:

Proceed with the operation for your model.

n KX-TG6811 series: page 3

Press and hold MN for about 5 seconds. (No registration tone)

n KX-TG6821 series: page 3

Press and hold MN for about 5 seconds, until the registration tone sounds.

R If all registered handsets start ringing, press MN again to stop, then repeat this step. (KX-TG6812)

R The next step must be completed within 90 seconds.

3Handset:

MOKN a Wait until “Base PIN” is displayed. a Enter the base unit PIN (default: “0000”). a MOKN

R If you forget your PIN, contact an authorised service centre.

R When the handset has been registered successfully, is displayed.

Note:

RWhile registering, “Base in registering” is displayed on all registered handsets. (KX-TG6812)

47

TG68xxSA(en)_0619_ver011.pdf 47

2013/06/19 17:43:18

Image 47

Panasonic KX-TG6821SA, KX-TG6812SA, KX-TG6811SA operating instructions Liquid damage, Registering a handset to the base unit

Contents

Thank you for purchasing a Panasonic product Digital Cordless PhoneDigital Cordless Answering System Table of Contents Model composition Feature differences Accessory item Accessory informationSupplied accessories Additional/replacement accessories For your safety Base unit location/avoiding noise Important safety instructionsBattery For best performance Routine care SpecificationsOther information Correct Incorrect Setting upBattery installation Connections Operation Operating time Battery chargingBattery level Icon Battery level Base unit ControlsHandset Line DisplayHandset display items Greeting Only is Display language Turning the power on/offInitial settings Date and time Dialling modeUsing the Smart Function Key NR key Smart Function Key NR key Setting the Smart Function Key One touch eco mode Answering calls Making calls Useful features during a call Handset equalizer Power back-up operationKey lock Handset noise reduction NR key When only 1 handset is registered Making calls during a power failureContinuing a call during a power failure Phonebook MbN Phonebook a Mokn Speed dial Display the menu tree and direct command code table Programmable settings New Message Alert *2 Outgoing Call Settings Number of Rings *2 2-7 RingsMemo Alarm Alarm1-3 Once Time Adjustment *2, *4 Caller ID On/Off Night Mode Ringer Setup Ringer VolumeHandset Ringer Volume Night Mode Power Failure Cancel Register *3 Line Setup Dial Mode *2 PulseMsec # 160 msec Privacy Mode *2, *5, *12 Repeater Mode *2 Caller Barred*2, *13 AlarmSpecial programming On 0 Off #173 Main menu Changing the start and end time Night modeTurning night mode on/off Setting the ring delay MeN Setting call restrictionChanging the handset name Incoming call barring Caller ID subscribers only Dect repeater Setting the repeater modeChanging the base unit PIN Personal Identification Number Increasing the range of the base unit Viewing the caller list and calling back Using Caller ID serviceCaller ID features Caller list Storing caller information to the phonebook Editing a caller’s phone number before calling backErasing selected caller information Erasing all caller information Memory capacity including your greeting message Answering systemTurning the answering system on/off Greeting message Operating the answering system during playback Listening to messages using the base unitMeN Using a pre-recorded greeting message Recording your greeting message Calling back Caller ID subscribers only Listening to messages using the handsetErasing all messages Operating the answering system New message alert by a call Advanced new message alerting featuresAudible message alert Remote operation Remote access codeUsing the answering system remotely Remote commands Number of rings before the unit answers a call Answering system settingsFor voice mail service subscribers Turning on the answering system remotely Selecting Greeting Only Caller’s recording time Voice mail service Transferring calls, conference calls IntercomHandset locator Character entry modes Character entry Cyrillic character table Extended 1 character tableExtended 2 character table Display message Error messagesCause/solution General use TroubleshootingProblem Making/answering calls, intercom Programmable settingsBattery recharge Answering system Caller ID Registering a handset to the base unit Liquid damage Deregistering a handset Index 2013/06/19 2013/06/19 For your future reference