Installation, Wall mounting | Panasonic KX-TG7652AZ, KX-TG7653AZ

DECT repeater

indicator

Status		Meaning
Green		Signal strength of the
(On)		base unit is strong.

Amber		Signal strength of the
(On)		base unit is weak.

Red		Out of base unit range.
(On)

Off		R The unit is not being
		used.
		R The power is off.

Installation

1Connect the unit.

R Use only the supplied Panasonic AC adaptor PQLV219AL.

Hook

Press plug firmly. (220-240 V AC, 50/60 Hz)

R When the unit is turned on, the indicator and indicator light amber for about 2 seconds.

2Confirm that the indicator and

indicator light green. (The unit is ready for use.)

R If the indicators do not light green, re-position the unit in a place where the indicators light green.

Note:

R The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

R The AC adaptor should be connected to a vertically oriented or

floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.

R The unit can support a maximum of 3 handsets at a time.

Setting the repeater mode

This repeater is pre-registered to the base unit and the default setting of repeater mode is “On”. You do not need to change this setting for initial use.

1MMENUN #138

2MbN: Select the desired setting. a MSAVEN a MOFFN

Note:

R After turning the repeater mode on or off, is displayed on the handset momentarily. This is normal and the handset can be used once is displayed.

Wall mounting

Note:

R Make sure that the wall and the fixing method are strong enough to support the weight of the unit.

R Drive the screws (not supplied) into the wall.

Screws

37 mm

Wall mounting template

37 mm

57

Image 57

Panasonic KX-TG7652AZ, KX-TG7653AZ operating instructions Installation, Wall mounting

Contents

Model shown is KX-TG7652 Before initial use, see Getting Started on Using Bluetooth Devices Caller ID ServiceVoice mail Service for Landline Introduction Series Model compositionModel No Base unit Handset Quantity Supplied accessories Accessory informationAccessory item/Part number Quantity KX-TG7652 KX-TG7653 AC adaptor for base unit and charger Expanding your phone system Additional/replacement accessories For your safety Important safety instructions For best performance Power consumption Base unit Setting up ConnectionsCorrect Wrong Battery charging Battery installationConfirm Charging is displayed Charge indicator During a power failure Intelligent eco mode ControlsBase unit Handset Display/IndicatorsTalk Moffn Mrecalln Mcall Waitn Use Cell 1/CELL 2 indicators on the base unitBase unit display item Meaning Greeting only Headset indicator on the base unit Initial settingsDate and time Example Registering a cellular phone Link to cell featureTrademarks Handset Ring as cell mode Link to cell settingsSelecting which unit receives cellular calls Moffn Connecting/disconnecting the cellular phone manually Cellular line only mode If you do not use the landlineAuto connection to the cellular phone To turn on Deregistering Bluetooth devices Changing the Bluetooth PIN Personal Identification NumberCellular line selection Storing your area code for local call Link to Cell Making cellular calls Making landline callsMcelln Answering calls Useful features during a call Privacy mode Using the other line during a conversationWhile another unit is on a cellular call While another unit is on a landline call MbN Hold a Mselectn To make a 2nd call To answer a 2nd callMbN Hold a Mselectn Shared phonebook Adding entriesCell 1, Cell Groups Finding and calling from a phonebook entryEditing entries Chain dial Erasing entries Display the menu tree and direct command code table Programmable settings Greeting Settings Ring count*1 RingsCheck greeting Pre-recorded*1 Device *4 Ringer volume BluetoothConnect *1 Add new Disconnect *1 Alarm Once SettingsAdjustment *1, *10 Auto Manual Auto connect Min Cell area Ringer setting Ringer volume Main menu Initial settingHandset *3, *7 Ringer volume Night mode Privacy mode*1 Set tel line*3 Set recall 900 msRepeater mode*1 Registration Register handset Condition is not good Newzealand = 600 ms Night mode AlarmSpecial programming Off Incoming call barring Caller ID subscribers only Changing the handset nameMbN Caller barred a Mclearn Operating additional units Registering a unitRegistering a handset to the base unit Additional handsets Deregistering a handset Caller ID features Using Caller ID serviceCall waiting and Caller ID compatible for Australia Private caller The caller For Caller ID Type II users Talking Caller IDMcall Waitn Phonebook name announcement Caller list Using a cellular lineRinger ID Viewing the caller list and calling back Erasing all caller information Erasing selected caller informationStoring caller information to the phonebook To erase your area code Copying phonebook from a cellular phone phonebook transfer Registering a headset to the base unit Operating a Bluetooth wireless headset using a landline Adjusting your headset receiver volume Base unit Switching from the base unit to your headsetCall sharing between your headset and the handset While the handset is on a landline call Turning the answering system on/off Answering system for landlineMemory capacity including your greeting message Call screening Greeting message Listening to messages using the base unit Erasing all messages Listening to messages using the handsetOperating the answering system Calling back Caller ID subscribers only Using the answering system remotely Remote access codeRemote commands Remote operation Turning on the answering system remotely Answering system settingsNumber of rings before the unit answers a call This will allow the voice mail to receive any messages Caller’s recording time MMENUN#305 MbN Select the desired setting. a Msaven a MoffnMessage alert Selecting Greeting only Voice mail service for landline Storing the voice mail VM access numberListening to voice mail messages Voice mail Service for Landline Handset locator IntercomTransferring calls, conference calls Making an intercom call For best performance Installation for Dect repeaterControls Mprogramn Wall mounting Installation AC adaptor cord Wall mounting Wall mounting template Charger25 mm Screws Hooks 25 mm Base no power Error messagesBusy Check tel line Error Failed Cause/solution Troubleshooting General use Problem Cause/solutionInvalid Cannot hear a dial tone Programmable settings Problem Cause/solution Battery recharge Problem Cause/solutionMaking/answering calls, intercom Problem Can make and answer cellular calls but cannot hear a sound Caller ID/Talking Caller ID Problem Cause/solution Using Bluetooth devices Problem Cause/solution Noise is heard during a call on the headset Answering system Problem Cause/solution Deregister Dect repeater ProblemRe-register Mlocatorn Repeating tone is heard while talking using the handset Bluetooth PIN Problem Cause/solutionLiquid damage Problem Exchange Program Warranty for New Zealand Index Index Page Page PNQX5357ZA TT0212MG0 For your future referenceSales Department