Panasonic PT-DW6300, PT-D5000 Lamp Select, Lamp Relay, Lamp Power, Standby Mode, REMOTE2 Mode

PROJECTOR SETUP menu

LAMP SELECT

You can select a lamp lighting pattern for using environment. Press I H to cycle through options, and the ENTER button.

DUAL	All lamps will light.
SINGLE	Selects a lamp with shorter duration of
	use.
LAMP1	Selects the Lamp unit 1.
LAMP2	Selects the Lamp unit 2.

NOTE:

•If, in the SINGLE, LAMP1 or LAMP2 mode, one lamp remains off or the currently active lamp exceeds 2 000*1 hours of cumulative operating time (when HIGH is selected as the LAMP POWER setting*2), the other lamp will light. If, in the DUAL mode, one lamp remains off or the currently active lamp exceeds 2 000*1 hours of cumulative operating time (when HIGH is selected as the LAMP POWER setting*2), the other lamp alone will light. However, if both lamps remain off or the 2 000*1 hours of cumulative operating time (when HIGH is selected as the LAMP POWER setting*2) are exceeded, the projector will enter the standby mode.

•The colours of the items indicate the status. Green: Current setting

Yellow: Current setting (when a lamp fails or fails to light)

Red: Lamp that has failed to light

White: Any other status.

•If the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently.

*1. 3 000 hours for PT-D5000 only.

*2. Not available for PT-D5000.

LAMP RELAY

If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use.

OFF	Deactive
00:00 - 23:00	1 hour interval from 00:00 to 23:00

NOTE:

•Only when DUAL or SINGLE is selected in LAMP SELECT, LAMP RELAY is available. If LAMP1 or LAMP2 is selected, LAMP RELAY function is not available.

LAMP SELECT	Repeated operation
setting
	LAMP1 and LAMP2 light alternately by the
SINGLE	set time, and the shorter duration of use
	lamp will light first.
	After both lamps light for the set time, only
	one lamp is turned off for 2 hours, then for
DUAL	only the other lamp for next 2 hours. The
	longer duration of use lamp will be turned off
	first.

LAMP POWER

(Not available for PT-D5000)

The luminance of the projection lamp can be changed depending on user’s needs or the viewing conditions.

HIGH	Set when high brightness is necessary.
LOW	Set when high brightness is not
	necessary.

NOTE:

•When set to LOW, it is possible to reduce power consumption, reduce operating noise and extend lamp service life.

STANDBY MODE

You can select the electrical consumption while in standby mode.

NOTE:

•With ECO setting, NETWORK function, RS-232Coutput and some of RS-232Ccommands are not available. When switch on the projector, projection will start about 10 seconds late.

RS-232C

This sets the communication parameters at the serial terminals.

(IN) BAUDRATE	Select 9600, 19200 or 38400.
(IN) PARITY	Select NONE, EVEN or ODD.
(OUT) BAUDRATE	Select 9600, 19200 or 38400.
(OUT) PARITY	Select NONE, EVEN or ODD.
RESPONSE(ID ALL)	Select ON or OFF.
GROUP	Select A to Z.
RESPONSE(ID GROUP)	Select ON or OFF.

REMOTE2 MODE

You can customise the REMOTE 2 IN terminal function.

DEFAULT The pin assignment of the REMOTE 2 IN terminal is used as the projector default setting.

USER For changing an optional input module or customising the pin assignments.

PIN1	GND
PIN2	POWER H NONE
	RGB1 H RGB2 H VIDEO H S-VIDEO H DVI-
PIN3 - PIN7	D H BALLAST VERSION H REWIND ALL
	FILTER H NONE
PIN8	SHUTTER H NONE
PIN9	ENABLE H DISABLE

Settings

ENGLISH - 29