![](/images/new-backgrounds/1205236/20523659x1.webp)
PROJECTOR SETUP menu
Settings
STATUS
You can see the status of the projector about the following items.
Items | Description | |
INPUT | Displays the input selection state. | |
NAME | Displays the input signal name. | |
SIGNAL FREQUENCY | Displays the frequency of the input | |
signal. | ||
| ||
PROJECTOR RUNTIME | Displays the projector runtime. | |
LAMP1 | Displays the lighting time of LAMP1. | |
LAMP2 | Displays the lighting time of LAMP2. | |
INTAKE AIR TEMP. | Displays the intake air temperature of | |
the projector. | ||
| ||
OPTICS MODULE TEMP. | Displays the temperature inside the | |
projector. | ||
| ||
AROUND LAMP TEMP. | Displays the temperature around the | |
lamp of the projector. | ||
| ||
REMAINING FILTER | Displays the filter runtime. | |
QUANTITY | Displays the filter remaining quantity. | |
PROJECTOR TYPE | Displays type of projector. | |
SERIAL NUMBER | Displays the serial number of the | |
projector. | ||
| ||
MAIN VERSION | Displays the main version of the | |
firmware of the projector unit. | ||
| ||
SUB VERSION | Displays the sub version of the | |
firmware of the projector unit. | ||
| ||
NETWORK VERSION | Displays the network version of the | |
projector unit. | ||
| ||
ON COUNT |
| |
POWER ON TIMES | Displays the number of times the | |
power has been tuned on. | ||
LAMP1 ON | Displays the number of times LAMP1 | |
| has been lit. | |
LAMP2 ON | Displays the number of times LAMP2 | |
has been lit. | ||
SHUTTER | Displays the number of times the | |
shutter function has been used. | ||
LAMP1 LOW * | Displays the LAMP1 lighting time with | |
LOW setting in LAMP POWER. | ||
| ||
HIGH * | Displays the LAMP1 lighting time with | |
HIGH setting in LAMP POWER. | ||
| ||
LAMP2 LOW * | Displays the LAMP2 lighting time with | |
LOW setting in LAMP POWER. | ||
| ||
HIGH * | Displays the LAMP2 lighting time with | |
HIGH setting in LAMP POWER. | ||
| ||
NUMBER OF ENTRY | Displays the number of registered | |
SIGNAL | signals. | |
REMOTE2 STATUS | Displays REMOTE 2 IN control status. |
* Not available for
FILTER COUNTER RESET
After you replaced the Auto Cleaning Filter (ACF), REMAINING FILTER of STATUS need to be reset to "0".
1.Press the ENTER button.
2.Select OK by pressing I, then press the ENTER button.
3.The REMAINING FILTER of STATUS will be reset to “0”.
Display the STATUS and confirm the figure.
NOTE:
•See “Replacing the Auto Cleaning Filter (ACF)” in the operating instructions booklet that is provided with the projector.
NO SIGNAL SHUT-OFF
You can set the timer to switch off the power of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 10 to 90 minutes at intervals of 10 minutes.
|
| DISABLE |
| ||
FG |
|
| FG | ||
|
|
|
|
| |
10 MIN. |
|
| 90 MIN. | ||
FG |
|
| FG | ||
|
|
|
|
| |
20 MIN. |
|
| 80 MIN. | ||
FG |
|
| FG | ||
|
|
|
|
| |
30 MIN. |
|
| 70 MIN. | ||
FG |
|
| FG | ||
|
|
|
| ||
40 MIN. |
|
| 60 MIN. | ||
FG |
|
| FG | ||
|
|
|
|
|
|
|
| 50 MIN. |
|
FUNCTION BUTTON
You can assign a certain menu function to the FUNCTION button as shortcut. Press I H to select the required menu option, and the ENTER button.
Options | Functions | Refer | |
DISABLE | Deactivate the FUNCTION | - | |
button. | |||
|
| ||
SUB MEMORY LIST | Displays the assigned SUB | 34 | |
MEMORY LIST. | |||
|
| ||
SYSTEM SELECTOR | Switches SYSTEM SELECTOR | 17 | |
| options. |
| |
SYSTEM DAYLIGHT | Switches the SYSTEM | 17 | |
VIEW | DAYLIGHT VIEW setting. | ||
| |||
FREEZE | Freezes the image. | 27 | |
SIDE BY SIDE | Start the SIDE BY SIDE mode. | 27 |
ENGLISH - 30