58
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms Checks
Picture Sound
Interference Noisy Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Normal Picture No Sound
Volume
(Check whether the mute function has been activated on the remote control.)
Check if speakers are connected properly.
No Picture No Sound
Not plugged into AC outlet
Not switched on
Picture and Brightness/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No Picture Normal Sound
If a signal with a non-applicable colour system format, or frequency is input, only
the input terminal indication is displayed.
No Colour Normal Sound
Colour controls set at minimum level (see page 26, 27)
Colour system (see page 47)
No remote control operations can be performed. Check whether the batteries have discharged completely and, if they have not,
whether they were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a
strong uorescent light.
Check whether the remote control designed speci cally for use with the unit is
being used. (The unit cannot be operated by any other remote control.)
A cracking sound is sometimes heard from the unit.
If there is nothing wrong with the picture or sound, this is the sound of the cabinet
undergoing very slight contractions in response to changes in the room temperature.
There are no adverse effects on the performance or other aspects.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Adjust the position of the picture on the screen.
Areas at the top and bottom of the screen where
the image is missing appear when I use the zoom
function.
When using a video software program (such as a cinema size program) with a
screen wider than one in the 16:9 mode, blank areas separate from the images
are formed at the top and bottom of the screen.
I can hear sounds coming from inside the unit. When the power is turned on, a sound of the display panel being driven may be
heard: This is normal and not indicative of malfunctioning.
Parts of the unit become hot.
Even when the temperature of parts of the front, top and rear panels has risen, these
temperature rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly. Check the settings of “PC Power management”, “DVI-D Power management”,
“No signal power off” and “No activity power off” in the Setup menu. Any of them
may be set to “On (Enable)”. (see page 42, 45)
Power indicator is blinking in red.
There is possibility of malfunction. Please contact an Authorized Service Center.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the
type of input signal. However, this is not a malfunction.

Plasma Display panel

Symptoms Check
The screen darkens slightly
when bright pictures with minimal
movements are shown.
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
It takes a while for the picture
to appear.
The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As
such, it sometimes takes a few moments for the picture to appear when the power has been turned
on, when the input has been switched or when the images for the main picture and sub picture on
the two screens are swapped.
The edges of the images
icker.
Due to the characteristics of the system used to drive the panel, the edges may appear to icker in
the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of
images in the 4:3 mode changes.
When viewing the side panels at the “High” or “Mid” setting, the brightness on both sides may change
depending on the kind of program shown: This is normal and not indicative of malfunctioning.
Some parts of the screen do
not light up.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Image retention appears
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed
in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from xed image use is not an
operating defect and as such is not covered by the Warranty.
This product is not designed to display xed images for extended periods of time.
Whirring sounds can be heard
from the display unit.
The display unit is tted with a cooling fan to dissipate heat generated during normal use. The whirring
sound is caused by rotation of the fan and is not a malfunction.