Accessories Supply | Panasonic TH-50PB2W, TH-65PB2W specification

Accessories

Accessories Supply

Check that you have the accessories and items shown

Operating	Software CD-ROM × 1	Remote Control		Batteries for the Remote
Instruction book		Transmitter		Control Transmitter
	• Panasonic WhiteBoard Software N2QAYB000691			(R6 (UM3) Size × 2)
	• Operating Instructions
	Display Operations
	Network Operations
	Electronic Pen Operations
	• Software license statements
	GNU GENERAL PUBLIC LICENSE
	GNU LESSER GENERAL PUBLIC LICENSE
Power supply cord	Clamper × 1	Ferrite core × 2	Electronic Pen set
	TMME289	J0KG00000014	Electronic Pen set
	TMME289	J0KG00000014

Refer to “Operating Instructions,

Electronic Pen Operations”.

Use the Ferrite cores to comply with the EMC standard. (refer to “Operating Instructions, Network Operations”)

Remote Control Batteries

Requires two R6 batteries.

1.Pull and hold the hook, then open the battery cover.

2. Insert batteries - note correct	3. Replace the cover.
polarity ( + and -).
“R6 (UM3)” size

-

+-+

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.

Observe the following precaution:

1.Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not combine a used battery with a new one.

3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5.Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.

6.Do not burn or breakup batteries.

7.Batteries must not be exposed to excessive heat such as sunshine, ﬁre or the like.

7

Image 7

Panasonic TH-50PB2W, TH-65PB2W operating instructions Accessories Supply, Remote Control Batteries

Contents

Operating Instructions Display Operations Table of Contents Important Information Important Safety NoticeTrademark Credits Transport only in upright position Safety PrecautionsSetup Do not place any objects on top of the Plasma Display When using the Plasma Display Safety PrecautionsIf problems occur during use Do not burn or breakup batteries Electric shocks can result if this is not done Accessories Supply AccessoriesRemote Control Batteries AC cord connection and ﬁxing, cable ﬁxing Connections Video equipment connection Speaker connectionConnections Video and Component / RGB in connection DVI-D in connection DVI-D Input ConnectorSignal Name Hdmi connection PC Input Terminals connection Signal Names for Mini D-sub 15P Connector Communication parameters CommandSerial Terminals connection Computer Starting up the network Power On / Off Power On / Off Slot Input Input terminal in Terminal Board Selecting the input signalPC Network Whiteboard Video COMPONENT* Hdmi DVI PC Network Whiteboard Slot Input Video Component Hdmi DVI Brightness Sensor Remote control sensorInput button Input signal selection see Basic Controls Basic Controls ECO Mode ECO Aspect Controls All Aspect mode Digital Zoom PIP Mode Multi PIP SettingsUsing Two Screen Display On-Screen Menu Displays Using Remote Control Adjusting Pos./SizeAuto mode Adjust so that any such noise is minimized Adjusting Pos./Size 2k1k Clamp Position During Component/PC input signalOptimum value for Clamp Position adjustment Is adjusted as follows For 2k1k signals Picture Adjustments Picture Adjustments Advanced settings MY Picture MEMORY1 Picture Proﬁles Select All delete Saving proﬁlesPicture Proﬁles Example Specifying MY Picture Renaming proﬁles Loading proﬁlesEditing proﬁles Deleting proﬁles SDI Sound Output Sound Adjustment Network Setup Setup menuSetup menu screen Day/Time Setup Day/Time Setup / On/Off Timer SetupOn/Off Timer Setup Slot Input Network Touch-Pen Settings Unpairing Touch-Pen SettingsStandby pen charging mode Pairing Multi PIP Multi PIP Settings Function selection Mode selectionStart setting Screensaver For preventing image retention Screensaver For preventing image retention Setup of Screensaver Time Image Retention Reduction Menu Extended life settingsPicture Mode Contrast Reduces screen image retention Nanodrift Saver Express settingsNanodrift Mode Reduces screen image retention Set each menu Select Custom settingsReset Adjust ECO Mode ECO Mode settings Customizing the Input labels Input SLOT* Input Whiteboard Function Button Settings Display orientation No activity power offMenu Display Duration / OSD Brightness OSD Language Component RGB Setup for Input SignalsComponent / RGB-in select YUV / RGB-in select Setup for Input Signals Signal menu SDI Through Setting RGB sync signalSetting Component sync signal Sync Sets the three NR functions separately Input signal displayNoise reduction Advanced NR Press for more than 3 seconds. Press to select Options Options Adjustments Input lock See Options Adjustments Studio Gain Normalisation Weekly Command Timer Press to select Time / Command Press to select a command numberPress to select Command No Command setting screen Audio input select Hold down for over 3 seconds Set Touch Panel mode to On Select AdjustCalibration mode When the menu is not displayed normal screen Primary Input, Secondary Input Input SearchInput Search PC Network Slot Input Video Component Hdmi DVI Plasma Display panel Troubleshooting 149 List of Aspect Modes Mark Applicable input signal Applicable Input Signals Shipping condition Applicable Input SignalsVideo input Video Command list of Weekly Command Timer TH-50PB2W TH-65PB2W Speciﬁcations Customer’s Record This product incorporates the following software