Panasonic TQBJ0299-3 E, EDGE BLENDING

ADVANCED MENU

ENGLISH - 23

Settings

(Not available for PT-D5000)

The built-in edge blending feature allows multiple projector

images to be seamlessly overlapped by adding a brightness

ramp. Press F G to select the required option.

QAdjusting EDGE BLENDING

1. Select ON and press the ENTER button to display the

detailed options.

2. Switch between ON/OFF of the required connecting

edge.

3. Press I H to adjust the value of START and WIDTH.

WIDTH of the both projectors must be the same value.

QAdjusting with colour markers

You can adjust with colour markers, which indicate the

overlapping area.

1. Press G several times until MARKER is displayed.

2. Select MARKER and press I H to switch between ON/

OFF.

Green and red lines will be displayed.

Green line indicates START point, and red line indicates

WIDTH from START point.

Adjust START and WIDTH for superimposing the green line

to the red.

QSelecting gamma level

You can adjust gamma level of the lapping area for fine

adjustment.

1. Select GAMMA and press the ENTER button.

2. Press I H to cycle through the options.

Options are 2.2, 1.8 and 2.0.

3. Press the ENTER button to apply the setting.

EDGE BLENDING

OFF Deactive

ON

Adds a brightness ramp to the

overlapped area and adjustable the

overlapping position manually.

Vertical connecting

Horizontal connecting

Overlapped

Projector 1

LOWER: ON

Projector 2

UPPER: ON

Overlapped

Projector 1

RIGHT: ON

Projector 2

LEFT: ON

Projector 1 Projector 2

Overlapping area

Green lines

Red lines

Contents

Main E Getting Started Settings Appendix Index .......................................................................... 50 Contents Setting up.....................................................................3 Connections ..............................................................10 Menu Navigation .......................................................12 PICTURE menu..........................................................16 Setting up Screen Screen size and throw distance Projected image Shown as 16:10 JProjection distance by projection lens QPT-DZ6710/PT-DZ6700 16:9 (Unit: m) 16:10 (Unit: m) QPT-DW6300 16:10 (Unit: m) 16:9 (Unit: m) QPT-D6000/PT-D5000 16:10 (Unit: m) 16:9 (Unit: m) JCalculation formulas for projection distance by lens types PT-DZ6710/PT-DZ6700 PT-DW6300 PT-D6000/PT-D5000 E Geometric adjustment E Front leg adjusters and throwing angle Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly. E Connections Before connection to the projector Pin assignments and signal names JS-VIDEO IN JRGB2 IN JDVI-D IN E Connecting example: Computers Connecting example: AV equipment E Menu Navigation DISPLAY LANGUAGE POSITION PICTURE ADVANCED MENU DISPLAY OPTION PROJECTOR SETUP TEST PATTERN SIGNAL LIST page 33 SECURITY NETWORK E JDisplaying the main menu See INITIALIZE on page 31 to reset the settings. 4. Press the MENU button to return to the previous menu. Press the MENU button to display the main menu. PICTURE menu QAdjusting more detailed white balance PICTURE MODE CONTRAST BRIGHTNESS E WHITE GAIN SYSTEM DAYLIGHT VIEW SHARPNESS NOISE REDUCTION POSITION menu JAspect ratio options QDEFAULT QVID AUTO QS1 AUTO E JMenu items displaying pattern depends on signals QWhen ASPECT setting is DEFAULT QWhen ASPECT setting is THROUGH QWhen ASPECT setting is others QGEOMETRY:KEYSTONE Select KEYSTONE and press the ENTER button to display the options. QGEOMETRY:CURVED Select CURVED and press the ENTER button to display the options. E KEYSTONE E ADVANCED MENU QSetting range DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION E QAdjusting EDGE BLENDING QAdjusting with colour markers QSelecting gamma level EDGE BLENDING E QAdjusting brightness around borderline of the image area RASTER POSITION E DISPLAY OPTION menu You can switch the contrast mode for operating environment. JSCREEN FORMAT JSCREEN POSITION You can change the displaying position of the projecting area. Press I H to adjust the value. E You can prevent the display of waning messages. JDVI EDID You can switch the EDID setting and signal level for variable DVI signals. JDVI SIGNAL LEVEL E BACK COLOR STARTUP LOGO FREEZE SIDE BY SIDE E PROJECTOR SETUP menu PROJECTOR ID INSTALLATION HIGH ALTITUDE MODE COOLING CONDITION E You can select the electrical consumption while in standby mode. This sets the communication parameters at the serial terminals. You can customise the REMOTE 2 IN terminal function. LAMP SELECT E You can see the status of the projector about the following items. STATUS FILTER COUNTER RESET NO SIGNAL SHUT-OFF E DATE AND TIME SERVICE PASSWORD LOAD ALL USERS DATA SAVE ALL USERS DATA TEST PATTERN TEST PATTERN SIGNAL LIST JSIGNAL LIST and SUB MEMORY LIST JManaging the list and the registered data QRegistering a signal to the list QDisplaying the signal list and the status SIGNAL LIST JManaging the sub memory list QRegistering the current settings to the list QDisplaying the sub memory list and restoring the settings QDeleting a sub memory data SECURITY menu JEntering the SECURITY menu QAfter you change the password SECURITY PASSWORD SECURITY PASSWORD CHANGE E JCONTROL PANEL JREMOTE CONTROLLER MENU LOCK MENU LOCK PASSWORD NETWORK menu NETWORK STATUS You can display the current network status of the projector. Press the ENTER button to display. NETWORK SETUP NETWORK CONTROL Technical Information Network connection LAN terminal E JProjector Control Window JChange password QAdministrator mode Accessing with the web browser JProjector Control QBasic control Click the Basic control tab on the top. QDetail control JDetailed set up QNetwork config Click the Adjust clock tag on the top. QAdjust clock QPing test QE-mail set up Click the E-mail set up tag on the top. When all options are filled, click Submit. Error report sample E-mail report sample JSTATUS QProjector status Click (Detail) Click the Projector status tab on the top. Error information E JControl commands JPJLink security authorization PJLinkTMprotocol E See RS-232C on page 29. JConnection QSingle projector QMultiple projectors JBasic format JCable specifications (When connected to a computer) JControl commands E Projector set up in a meeting room Control panel located in a different room JPin assignments and control REMOTE 2 IN terminal E (PT-DZ6710/PT-DZ6700/PT-DW6300 only) Restoring the MENU LOCK PASSWORD to default QSide by Side function signal combination table QMovie signals Page Index Index