Panasonic TQBJ0299-3 Setting up

Getting Started

ENGLISH - 3

Setting up

When planning the projector and screen geometry, refer to the figures below and the information on the following

pages for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely

adjusted with the powered zoom lens and lens shifting mechanism.

Screen size and throw distance

L (LW/LT) Projection distance

SH Height of the projection area

SW Width of the projection area

HVertical distance between the lens centre level

and the bottom edge of the projected image.

SD Diagonal length of the projection area

NOTE:

• All following measurements and the calculation results are approximate and may differ slightly from the actual

measurements.

• The throw ratio is based on the value during projection onto an 80-inch screen size.

• Lens shift is not available when using the ET-DLE055, and so the height position (H) is SH/2.

• See the operating instructions that is provided with the projector.

• Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or

indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices™ in which case there is a

loss of warranty.

S

D

SW

H

SH

Screen

Projected image

Shown as 16:10

Contents

Main E Getting Started Settings Appendix Index .......................................................................... 50 Contents Setting up.....................................................................3 Connections ..............................................................10 Menu Navigation .......................................................12 PICTURE menu..........................................................16 Setting up Screen Screen size and throw distance Projected image Shown as 16:10 JProjection distance by projection lens QPT-DZ6710/PT-DZ6700 16:9 (Unit: m) 16:10 (Unit: m) QPT-DW6300 16:10 (Unit: m) 16:9 (Unit: m) QPT-D6000/PT-D5000 16:10 (Unit: m) 16:9 (Unit: m) JCalculation formulas for projection distance by lens types PT-DZ6710/PT-DZ6700 PT-DW6300 PT-D6000/PT-D5000 E Geometric adjustment E Front leg adjusters and throwing angle Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly. E Connections Before connection to the projector Pin assignments and signal names JS-VIDEO IN JRGB2 IN JDVI-D IN E Connecting example: Computers Connecting example: AV equipment E Menu Navigation DISPLAY LANGUAGE POSITION PICTURE ADVANCED MENU DISPLAY OPTION PROJECTOR SETUP TEST PATTERN SIGNAL LIST page 33 SECURITY NETWORK E JDisplaying the main menu See INITIALIZE on page 31 to reset the settings. 4. Press the MENU button to return to the previous menu. Press the MENU button to display the main menu. PICTURE menu QAdjusting more detailed white balance PICTURE MODE CONTRAST BRIGHTNESS E WHITE GAIN SYSTEM DAYLIGHT VIEW SHARPNESS NOISE REDUCTION POSITION menu JAspect ratio options QDEFAULT QVID AUTO QS1 AUTO E JMenu items displaying pattern depends on signals QWhen ASPECT setting is DEFAULT QWhen ASPECT setting is THROUGH QWhen ASPECT setting is others QGEOMETRY:KEYSTONE Select KEYSTONE and press the ENTER button to display the options. QGEOMETRY:CURVED Select CURVED and press the ENTER button to display the options. E KEYSTONE E ADVANCED MENU QSetting range DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION E QAdjusting EDGE BLENDING QAdjusting with colour markers QSelecting gamma level EDGE BLENDING E QAdjusting brightness around borderline of the image area RASTER POSITION E DISPLAY OPTION menu You can switch the contrast mode for operating environment. JSCREEN FORMAT JSCREEN POSITION You can change the displaying position of the projecting area. Press I H to adjust the value. E You can prevent the display of waning messages. JDVI EDID You can switch the EDID setting and signal level for variable DVI signals. JDVI SIGNAL LEVEL E BACK COLOR STARTUP LOGO FREEZE SIDE BY SIDE E PROJECTOR SETUP menu PROJECTOR ID INSTALLATION HIGH ALTITUDE MODE COOLING CONDITION E You can select the electrical consumption while in standby mode. This sets the communication parameters at the serial terminals. You can customise the REMOTE 2 IN terminal function. LAMP SELECT E You can see the status of the projector about the following items. STATUS FILTER COUNTER RESET NO SIGNAL SHUT-OFF E DATE AND TIME SERVICE PASSWORD LOAD ALL USERS DATA SAVE ALL USERS DATA TEST PATTERN TEST PATTERN SIGNAL LIST JSIGNAL LIST and SUB MEMORY LIST JManaging the list and the registered data QRegistering a signal to the list QDisplaying the signal list and the status SIGNAL LIST JManaging the sub memory list QRegistering the current settings to the list QDisplaying the sub memory list and restoring the settings QDeleting a sub memory data SECURITY menu JEntering the SECURITY menu QAfter you change the password SECURITY PASSWORD SECURITY PASSWORD CHANGE E JCONTROL PANEL JREMOTE CONTROLLER MENU LOCK MENU LOCK PASSWORD NETWORK menu NETWORK STATUS You can display the current network status of the projector. Press the ENTER button to display. NETWORK SETUP NETWORK CONTROL Technical Information Network connection LAN terminal E JProjector Control Window JChange password QAdministrator mode Accessing with the web browser JProjector Control QBasic control Click the Basic control tab on the top. QDetail control JDetailed set up QNetwork config Click the Adjust clock tag on the top. QAdjust clock QPing test QE-mail set up Click the E-mail set up tag on the top. When all options are filled, click Submit. Error report sample E-mail report sample JSTATUS QProjector status Click (Detail) Click the Projector status tab on the top. Error information E JControl commands JPJLink security authorization PJLinkTMprotocol E See RS-232C on page 29. JConnection QSingle projector QMultiple projectors JBasic format JCable specifications (When connected to a computer) JControl commands E Projector set up in a meeting room Control panel located in a different room JPin assignments and control REMOTE 2 IN terminal E (PT-DZ6710/PT-DZ6700/PT-DW6300 only) Restoring the MENU LOCK PASSWORD to default QSide by Side function signal combination table QMovie signals Page Index Index