Panasonic WV-CW974 RS485 Communication Parameters DIP Switch, Procedure to setup dip switch

DIP Switch 1								Unit	DIP Switch 1								Unit	DIP Switch 1								Unit
								Number									Number									Number
ON									ON									ON
1	2	3	4	5	6	7	8	69	1	2	3	4	5	6	7	8	78	1	2	3	4	5	6	7	8	87
ON									ON									ON
1	2	3	4	5	6	7	8	70	1	2	3	4	5	6	7	8	79	1	2	3	4	5	6	7	8	88
ON									ON									ON
1	2	3	4	5	6	7	8	71	1	2	3	4	5	6	7	8	80	1	2	3	4	5	6	7	8	89
ON									ON									ON
1	2	3	4	5	6	7	8	72	1	2	3	4	5	6	7	8	81	1	2	3	4	5	6	7	8	90
ON									ON									ON
1	2	3	4	5	6	7	8	73	1	2	3	4	5	6	7	8	82	1	2	3	4	5	6	7	8	91
ON									ON									ON
1	2	3	4	5	6	7	8	74	1	2	3	4	5	6	7	8	83	1	2	3	4	5	6	7	8	92
ON									ON									ON
1	2	3	4	5	6	7	8	75	1	2	3	4	5	6	7	8	84	1	2	3	4	5	6	7	8	93
ON									ON									ON
1	2	3	4	5	6	7	8	76	1	2	3	4	5	6	7	8	85	1	2	3	4	5	6	7	8	94
ON									ON									ON
1	2	3	4	5	6	7	8	77	1	2	3	4	5	6	7	8	86	1	2	3	4	5	6	7	8	95

Notes:

•When using the Unit Number “1 ~ 96” setting, the unit number setting needs to be configured using the RS485 SET UP menu. For details about configuring this setting, see step 2 on page 20.

•Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialization routine.

■RS485 Communication Parameters (DIP Switch 1)

Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can then change the settings as desired.

Table-2

DIP Switch 1								Setting Description
ON								This setting resets communication parameters to the factory default settings.
1	2	3	4	5	6	7	8
ON								BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1	2	3	4	5	6	7	8
ON								BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1	2	3	4	5	6	7	8
ON								BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1	2	3	4	5	6	7	8

■Procedure to setup dip switch 1

(1)Turn off the camera and use DIP Switch 1 to configure RS485 Communication Parameters as shown in Table-2.

(2)Turn on the camera.

This applies the setting you configured in step (1).

(3)Turn off the camera, use DIP Switch 1 to set the unit number (as shown in Table-1), and then turn the camera back on again.

-14-