Patton electronic 2635, 2621 instruction

Models 2603, 2621, and 2635 Getting Started Guide	3 • Initial Configuration

Installing an interface cable on the IPLink 2621’s X.21 interface port

The IPLink Model 2621 comes with an X.21 interface presented on a female DB-15 connector (see ﬁgure 7). This interface can be conﬁgured as a DTE (factory default), or as a DCE via internal conﬁguration jumper.

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

Ethernet connector		X.21 Interface connector
(RJ-45)		(DB-15)
	10/100
		Crossover
		MDI-X
Power	Ethernet	X.21 Interface

Power	10/100
Power		Crossover
	Ethernet	Crossover
	Ethernet	MDI-
		MDI-
		X

X.
21	Interface
	Interface

Figure 7. Rear view of the 2621 showing location of Ethernet and X.21 connectors

Hardware installation

31

Image 31

Patton electronic 2635, 2621 manual Ethernet connector Interface connector RJ-45 DB-15

Contents

IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsImpaired functioning General observations Factory default parameters General conventions Typographical conventions used in this document General Information Chapter contents General attributes IPLink Series High Speed Routers overview WAN Interfaces EthernetProtocol support PPP Support Security Logging or Smtp on events POST, Post errors, PPP/DHCP, IPFront Panel Status LEDs and Console Port Console port Rear panel connectors and switchesOn the rear panel from left to right are the following Ethernet port outlined in green Power connector General Information Product Overview Introduction Sync Serial Application Applications Overview Initial Conﬁguration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cord Initial Configuration Do the following Installing the Ethernet cable PC Conﬁguration IP address modiﬁcationIP address has now been successfully changed Web Operation and Conﬁguration Model 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN Connections Basic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Serial Interface WAN Serial Port ConﬁgurationVariables T1/E1 Interface Conﬁguration Web Interface Conﬁguration Web Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 Operation Conﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1 Serial Port Configuration PPP Bridged WAN Services WAN Services PPP Conﬁguration WAN Service ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP Routed PPP Routed Conﬁguration menu Click on Create Edit IP address of WAN port Click the Update button PPP link status LMI Management Frame Relay links Username blank Password blank Click on the Create buttonLMI Conﬁguration Web Conﬁguration Methods Dlci Number Use Frame Relay Conﬁguration Frame Relay bridged creation Frame Relay bridged Central site conﬁguration Relay Frame Relay Routed Description FR routed Frame Relay Channel Routed conﬁguration IP route for Frame Relay routed application Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new service Click on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfaces Security conﬁguration home Click on the hyperlink New Policy... See ﬁgure Conﬁguring Security Policies Firewall Portﬁlters Enabling the FirewallDeleting a security Policy You can now ping between the two networks Security Triggers Conﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDS Security Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp Server Dhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnet Next section see ﬁgure 58. has three parameters IP Addresses to be available on this subnet DNS server option information Example based on default range of IP address pool Conﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp Relay Dhcp Relay webpage Conﬁguring the DNS Relay DNS Relay DNS Relay conﬁguration webpage IP Services CLI Conﬁguration IP ServicesNext command disables the WEB server WEB Server Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser Authentication Access the conﬁguration and status of the alarms Alarm Alarm & Alarm Error Log conﬁguration Remote Access Backup/Restore UpdateSave Restart Website Settings Snmp Daemon Error Log Snmp Daemon conﬁguration System Tools Sntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration Parameters Sntp Client General Conﬁguration Parameters System Clock Setting Conﬁguration of the internal system calendar clock System Status Port Connection Status System Status Hardware Status LAN StatusMAC address the MAC address of the Ethernet port WAN Status Status LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceReturns for credit Return for credit policy EMC Appendix a Compliance information FCC Part 68 Acta Statement Model 2603 only ComplianceRadio and TV Interference FCC Part CE Declaration of Conformity Industry Canada Notice 2603 Model only Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial Interface PPP Support Protocol SupportManagement VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supply Appendix C Cable Recommendations Adapter Ethernet Cable Appendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port Assuming the MDI-X switch is in the out positionRJ-45 non-shielded RS-232 console port EIA-561 Serial port 35 M/34 and DB-25 Connector Pin No Circuit Signal Name Direction 21 DB-15 Connector Pin No Signal E1/T1 RJ-48C Connector Appendix E Command Line Interface CLI Operation Local VT-100 emulation Using the ConsoleCLI Terminology Produces a list of numbered transport objects Then Another example shows when the user must provide a parameter Adding new users Administering user accountsSetting user passwords Enter the new password twice as prompted For example, to change the security level for fred, enter Changing user settingsControlling login access Controlling user access