Manuals
/
Patton electronic
/
Computer Equipment
/
Network Hardware
Patton electronic
4900 user manual SmartNode, IpChannel Bank, User Manual, Sales Office +1 301
Models:
4900
1
1
76
76
Download
76 pages
36.79 Kb
1
2
3
4
5
6
7
8
<
>
Specs
Install
Network diagram
Warranty
Dimension
The Model SN4900 can only be configured with two AC power
Connecting cables
Reset button behavior
Command
Factory-default IP settings
Page 1
Image 1
SmartNode 4900
IpChannel Bank
User Manual
Sales Office:
+1 (301)
975-1000
Technical Support:
+1 (301)
975-1007
E-mail:
support@patton.com
WWW:
www.patton.com
Part Number:
07MSN4900-GS,
Rev. H
Revised:
February 8, 2012
Page 2
Page 1
Image 1
Page 2
Contents
IpChannel Bank
SmartNode
User Manual
Sales Office +1 301
7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301
Summary Table of Contents
Summary Table of Contents
Table of Contents
Table of Contents
Hardware installation
4 Getting started with the SmartNode 4900 Series
Table of Contents
5 LEDs status and monitoring
6 Contacting Patton for assistance
Factory Configuration
Specifications
Port pin-outs
E End user license agreement
Warranty
Table of Contents
Installation checklist
Accessories
List of Figures
List of Tables
Audience
About this guide
Structure
impaired functioning
Precautions
Note A note presents additional information or interesting sidelights
Strictly follow the warning instructions to avoid personal injury
The Model SN4900 can only be configured with two AC power
Safety when working with electricity
protected by a circuit breaker
has earth ground
General observations
Preventing Electrostatic Discharge Damage
Clean the case with a soft slightly moist anti-static cloth
Protect the unit from moisture, vapors, and corrosive liquids
General conventions
Typographical conventions used in this document
Garamond blue type
Chapter
Chapter contents
General information
SmartNode 4900 Series overview
SN4912/JSx/RUI 12 FXS ports SN4916/JSx/RUI 16 FXS ports
SmartNode 4900 Series detailed description
SN4924/JSx/RUI 24 FXS ports SN4932/JSx/RUI 32 FXS ports
SN4912/JO/RUI 12 FXO ports SN4916/JO/RUI 16 FXO ports
LED Condition
SmartNode 4900 Series front panel
Description
1 General information
SmartNode 4900 Series rear panels
Model SN4932
Expansion port
Expansion
Reset button behavior
Chapter contents
Chapter 2 Applications overview
Introduction
Multiservice carrier access over leased lines
SmartNode 4900 Series applications
Bulk analog line extensions
Enterprise FXS concentration and extension over IP and T1/E1
Figure 6. Bulk analog line extensions application
Chapter contents
Hardware installation
Chapter
Create a network diagram see section “Network information” on page
Planning the installation
Verify power source reliability see section “Power source” on page
Introduction
appendix F, “Installation checklist” on page
Installation checklist
Site log
Configuration tools
Network diagram
AC Power Mains
Network information
IpChannel Bank chassis installation
Installing the IpChannel Bank
Location and mounting requirements
Unpacking the Model SN4900 series IpChannel Bank
Connecting the FXS ports
Connecting cables
Connecting the FXO ports
Figure 9. Cross-over RJ-45-to-RJ-45 Ethernet cable diagram
Connecting the Ethernet ports
Connecting the serial port
Connecting the EIA-561 RS-232 configuration port DCE configured
V.35 Interface DB-25
X.21 interface DB-15
Grounding the Model SN4900-AC and DC units
Connecting power
Installing the power cables-AC units
3. Repeat steps 1 and 2 to install the remaining power cable
Installing the power cables-DC units
3. Insert the stripped end of the positive lead into the +DC input of the terminal block. Tighten the screw until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the -DC input of the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires
SmartNode 4900 Series
Chapter 4 Getting started with the
Chapter contents
Figure 15. Connecting the SmartNode to the network
Figure 14. Connecting the SmartNode to your laptop PC
Introduction
4 Getting started with the SmartNode 4900 Series
Factory-default IP settings
1. Configure IP address
Terminal emulation program settings Asynchronous 9600 bps No parity
Connect to the RS-232 console port
e.g. HyperTerm
8 bit 1 stop bit No flow control
Changing the WAN IP address
Login
3. Loading the configuration optional
2. Connecting the SmartNode to the network
Start Bootloader
Bootloader
Load a new application image SmartWare via TFTP
Start-up with factory configuration
Command
RedBoot fis load
Download it after starting up SmartWare with the following command
Load a new application image SmartWare via the serial link
Additional information
Chapter contents
Chapter 5 LEDs status and monitoring
5 LEDs status and monitoring
Status LEDs
Chapter contents
Chapter 6 Contacting Patton for assistance
Warranty coverage
Warranty Service and Returned Merchandise Authorizations RMAs
Contact information
Patton support headquarters in the USA
Returns for credit
Out-of-warranty service
Return for credit policy
RMA numbers
Chapter contents
Appendix A Compliance information
Compliance
Safety compliance
Radio and TV interference FCC Part
CE Declaration of Conformity
A Compliance information
Watchfield Swindon, Wilts SN6 8TD, UK
Authorized European Representative
Industry Canada Notice FXO Ports
FCC Part 68 ACTA Statement FXO ports
FCC Part 68 ACTA Statement FXO ports
Chapter contents
Appendix B Specifications
Voice connectivity - FXO
Voice connectivity - FXS
Ethernet interface
Console port
FXS ports
Voice processing signaling dependent
FXO ports
PPP and Frame-Relay support
IP services
Voice signaling
Voice routing-session router
Weight and power dissipation
Dimensions
Temperature
Management
Identification of the SmartNode devices via SNMP
Power supply
Universal AC version
DC version
Chapter contents
Appendix C Port pin-outs
Introduction
Ethernet 10Base-T and 100Base-T port
Console port
Figure 19. EIA-561 RJ-45 8-pin port
Sync Serial port
Sync Serial port
Blue
FXS and FXO ports
Yellow
Blue
Green
Yellow
Black
Black
Black
Black
Pair
Chapter contents
Appendix D Factory Configuration
Introduction
D Factory Configuration
Introduction
Chapter contents
Appendix E End user license agreement
Warranty
End User License Agreement
End User License Agreement
5. Warranty
1. Definitions
2. Title
7. Other licenses
6. Termination
Chapter contents
Appendix F Installation checklist
Introduction
F Installation checklist
Chapter contents
Appendix G Accessories
Description
Introduction
Part Number
