Manuals / Patton electronic / Computer Equipment / Network Hardware

Patton electronic 4900 user manual Applications overview, Chapter contents

Models: 4900

1 76

Download 76 pages 36.79 Kb

Page 21

Chapter 2 Applications overview
Chapter contents
Introduction	22
SmartNode 4900 Series applications	22
Multiservice carrier access over leased lines	22
Enterprise FXS concentration and extension over IP and T1/E1	23
Bulk analog line extensions	23

21

Image 21

Patton electronic 4900 user manual Applications overview, Chapter contents

Contents

IpChannel Bank SmartNodeUser Manual Sales Office +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents Hardware installation4 Getting started with the SmartNode 4900 Series Table of Contents5 LEDs status and monitoring 6 Contacting Patton for assistanceFactory Configuration SpecificationsPort pin-outs E End user license agreementWarranty Table of ContentsInstallation checklist AccessoriesList of Figures List of Tables About this guide AudienceStructure impaired functioning PrecautionsNote A note presents additional information or interesting sidelights Strictly follow the warning instructions to avoid personal injuryThe Model SN4900 can only be configured with two AC power Safety when working with electricityprotected by a circuit breaker has earth groundGeneral observations Preventing Electrostatic Discharge DamageClean the case with a soft slightly moist anti-static cloth Protect the unit from moisture, vapors, and corrosive liquidsTypographical conventions used in this document General conventionsGaramond blue type Chapter contents ChapterGeneral information SmartNode 4900 Series overview SN4912/JSx/RUI 12 FXS ports SN4916/JSx/RUI 16 FXS ports SmartNode 4900 Series detailed descriptionSN4924/JSx/RUI 24 FXS ports SN4932/JSx/RUI 32 FXS ports SN4912/JO/RUI 12 FXO ports SN4916/JO/RUI 16 FXO portsSmartNode 4900 Series front panel LED ConditionDescription 1 General information SmartNode 4900 Series rear panelsModel SN4932 Expansion portExpansion Reset button behaviorChapter contents Chapter 2 Applications overviewMultiservice carrier access over leased lines IntroductionSmartNode 4900 Series applications Enterprise FXS concentration and extension over IP and T1/E1 Bulk analog line extensionsFigure 6. Bulk analog line extensions application Hardware installation Chapter contentsChapter Create a network diagram see section “Network information” on page Planning the installationVerify power source reliability see section “Power source” on page IntroductionInstallation checklist appendix F, “Installation checklist” on pageSite log Configuration tools Network diagramAC Power Mains Network informationIpChannel Bank chassis installation Installing the IpChannel BankLocation and mounting requirements Unpacking the Model SN4900 series IpChannel BankConnecting cables Connecting the FXS portsConnecting the FXO ports Figure 9. Cross-over RJ-45-to-RJ-45 Ethernet cable diagram Connecting the Ethernet portsConnecting the serial port Connecting the EIA-561 RS-232 configuration port DCE configuredV.35 Interface DB-25 X.21 interface DB-15Grounding the Model SN4900-AC and DC units Connecting powerInstalling the power cables-AC units 3. Repeat steps 1 and 2 to install the remaining power cable Installing the power cables-DC units3. Insert the stripped end of the positive lead into the +DC input of the terminal block. Tighten the screw until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the -DC input of the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires Chapter 4 Getting started with the SmartNode 4900 SeriesChapter contents Figure 15. Connecting the SmartNode to the network Figure 14. Connecting the SmartNode to your laptop PCIntroduction 4 Getting started with the SmartNode 4900 SeriesFactory-default IP settings 1. Configure IP addressTerminal emulation program settings Asynchronous 9600 bps No parity Connect to the RS-232 console porte.g. HyperTerm 8 bit 1 stop bit No flow controlChanging the WAN IP address Login3. Loading the configuration optional 2. Connecting the SmartNode to the networkStart Bootloader BootloaderLoad a new application image SmartWare via TFTP Start-up with factory configurationCommand RedBoot fis loadDownload it after starting up SmartWare with the following command Load a new application image SmartWare via the serial link Additional informationChapter contents Chapter 5 LEDs status and monitoring5 LEDs status and monitoring Status LEDsChapter contents Chapter 6 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationCompliance Safety complianceRadio and TV interference FCC Part CE Declaration of ConformityWatchfield Swindon, Wilts SN6 8TD, UK A Compliance informationAuthorized European Representative FCC Part 68 ACTA Statement FXO ports Industry Canada Notice FXO PortsFCC Part 68 ACTA Statement FXO ports Chapter contents Appendix B SpecificationsVoice connectivity - FXO Voice connectivity - FXSEthernet interface Console portFXS ports Voice processing signaling dependentFXO ports PPP and Frame-Relay supportVoice signaling IP servicesVoice routing-session router Weight and power dissipation DimensionsTemperature ManagementIdentification of the SmartNode devices via SNMP Power supplyUniversal AC version DC versionChapter contents Appendix C Port pin-outsIntroduction Ethernet 10Base-T and 100Base-T portConsole port Figure 19. EIA-561 RJ-45 8-pin portSync Serial port Sync Serial portBlue FXS and FXO portsYellow BlueGreen YellowBlack BlackBlack BlackPair Chapter contents Appendix D Factory ConfigurationD Factory Configuration IntroductionIntroduction Chapter contents Appendix E End user license agreementWarranty End User License AgreementEnd User License Agreement 5. Warranty1. Definitions 2. Title7. Other licenses 6. TerminationChapter contents Appendix F Installation checklistIntroduction F Installation checklistChapter contents Appendix G AccessoriesIntroduction DescriptionPart Number