Manuals / Patton electronic / Computer Equipment / Network Hardware

Patton electronic 4900 user manual Pair

Models: 4900

1 76

Page 67

SmartNode 4900 User Manual	C • Port pin-outs

Table 17. Band marked color-codes for the 50-pin RJ-21X connector (Continued)

Wire/Color Code		Tip & Ring	Pair Number	50 Pin
				50 Pin
Main color	Stripe			Positions
				Positions


Yellow	Brown	Tip 19	Pair 19	44
Brown	Yellow	Ring 19	Pair 19	19
Brown	Yellow	Ring 19		19

Yellow	Slate	Tip 20	Pair 20	45
Slate	Yellow	Ring 20	Pair 20	20
Slate	Yellow	Ring 20		20

Violet	Blue	Tip 21	Pair 21	46
Blue	Violet	Ring 21	Pair 21	21
Blue	Violet	Ring 21		21

Violet	Orange	Tip 22	Pair 22	47
Orange	Violet	Ring 22	Pair 22	22
Orange	Violet	Ring 22		22

Violet	Green	Tip 23	Pair 23	48
Green	Violet	Ring 23	Pair 23	23
Green	Violet	Ring 23		23

Violet	Brown	Tip 24	Pair 24	49
Brown	Violet	Ring 24	Pair 24	24
Brown	Violet	Ring 24		24

Violet	Slate	Tip 25	Pair 25	50
Slate	Violet	Ring 25	Pair 25	25
Slate	Violet	Ring 25		25

FXS and FXO ports

Page 67

Image 67

Contents

Sales Office +1 301 SmartNodeIpChannel Bank User Manual7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Hardware installation Table of ContentsSummary Table of Contents Table of Contents6 Contacting Patton for assistance Table of Contents4 Getting started with the SmartNode 4900 Series 5 LEDs status and monitoringE End user license agreement SpecificationsFactory Configuration Port pin-outsAccessories Table of ContentsWarranty Installation checklistList of Figures List of Tables Audience About this guideStructure Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightshas earth ground Safety when working with electricityThe Model SN4900 can only be configured with two AC power protected by a circuit breakerProtect the unit from moisture, vapors, and corrosive liquids Preventing Electrostatic Discharge DamageGeneral observations Clean the case with a soft slightly moist anti-static clothGeneral conventions Typographical conventions used in this documentGaramond blue type Chapter Chapter contentsGeneral information SmartNode 4900 Series overview SN4912/JO/RUI 12 FXO ports SN4916/JO/RUI 16 FXO ports SmartNode 4900 Series detailed descriptionSN4912/JSx/RUI 12 FXS ports SN4916/JSx/RUI 16 FXS ports SN4924/JSx/RUI 24 FXS ports SN4932/JSx/RUI 32 FXS portsLED Condition SmartNode 4900 Series front panelDescription Expansion port SmartNode 4900 Series rear panels1 General information Model SN4932Expansion Reset button behaviorChapter contents Chapter 2 Applications overviewIntroduction Multiservice carrier access over leased linesSmartNode 4900 Series applications Bulk analog line extensions Enterprise FXS concentration and extension over IP and T1/E1Figure 6. Bulk analog line extensions application Chapter contents Hardware installationChapter Introduction Planning the installationCreate a network diagram see section “Network information” on page Verify power source reliability see section “Power source” on pageappendix F, “Installation checklist” on page Installation checklistSite log Network information Network diagramConfiguration tools AC Power MainsUnpacking the Model SN4900 series IpChannel Bank Installing the IpChannel BankIpChannel Bank chassis installation Location and mounting requirementsConnecting the FXS ports Connecting cablesConnecting the FXO ports Figure 9. Cross-over RJ-45-to-RJ-45 Ethernet cable diagram Connecting the Ethernet portsX.21 interface DB-15 Connecting the EIA-561 RS-232 configuration port DCE configuredConnecting the serial port V.35 Interface DB-25Grounding the Model SN4900-AC and DC units Connecting powerInstalling the power cables-AC units 3. Repeat steps 1 and 2 to install the remaining power cable Installing the power cables-DC units3. Insert the stripped end of the positive lead into the +DC input of the terminal block. Tighten the screw until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the -DC input of the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires SmartNode 4900 Series Chapter 4 Getting started with theChapter contents 4 Getting started with the SmartNode 4900 Series Figure 14. Connecting the SmartNode to your laptop PCFigure 15. Connecting the SmartNode to the network IntroductionFactory-default IP settings 1. Configure IP address8 bit 1 stop bit No flow control Connect to the RS-232 console portTerminal emulation program settings Asynchronous 9600 bps No parity e.g. HyperTermChanging the WAN IP address Login3. Loading the configuration optional 2. Connecting the SmartNode to the networkStart Bootloader BootloaderRedBoot fis load Start-up with factory configurationLoad a new application image SmartWare via TFTP CommandDownload it after starting up SmartWare with the following command Load a new application image SmartWare via the serial link Additional informationChapter contents Chapter 5 LEDs status and monitoring5 LEDs status and monitoring Status LEDsChapter contents Chapter 6 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCE Declaration of Conformity Safety complianceCompliance Radio and TV interference FCC PartA Compliance information Watchfield Swindon, Wilts SN6 8TD, UKAuthorized European Representative Industry Canada Notice FXO Ports FCC Part 68 ACTA Statement FXO portsFCC Part 68 ACTA Statement FXO ports Chapter contents Appendix B SpecificationsConsole port Voice connectivity - FXSVoice connectivity - FXO Ethernet interfacePPP and Frame-Relay support Voice processing signaling dependentFXS ports FXO portsIP services Voice signalingVoice routing-session router Management DimensionsWeight and power dissipation TemperatureDC version Power supplyIdentification of the SmartNode devices via SNMP Universal AC versionChapter contents Appendix C Port pin-outsFigure 19. EIA-561 RJ-45 8-pin port Ethernet 10Base-T and 100Base-T portIntroduction Console portSync Serial port Sync Serial portBlue FXS and FXO portsYellow BlueYellow GreenBlack BlackBlack BlackPair Chapter contents Appendix D Factory ConfigurationIntroduction D Factory ConfigurationIntroduction End User License Agreement Appendix E End user license agreementChapter contents Warranty2. Title 5. WarrantyEnd User License Agreement 1. Definitions7. Other licenses 6. TerminationChapter contents Appendix F Installation checklistIntroduction F Installation checklistChapter contents Appendix G AccessoriesDescription IntroductionPart Number