Manuals / Patton electronic / Computer Equipment / Network Hardware

Patton electronic 4900 Management, Operating environment, System, Dimensions, Temperature

Models: 4900

1 76

Download 76 pages 36.79 Kb

Page 59

SmartNode 4900 User Manual	B • Specifications

802.1p VLAN tagging

IPSEC AH & ESP Modes

Manual Key; IKE optional

AES/DES/3DES Encryption

Management

Industry standard CLI with local console (RJ-45, RS-232) and remote Telnet access

TFTP configuration & firmware loading

SNMP v1 agent (MIB II and private MIB)

Built-in diagnostic tools (trace, debug)

Operating environment

Temperature

Operating range: 32–104°F (0–40°C)

Internal temperature: Available in real-time on the IpChannel Bank web pages

Humidity

5 to 90% relative humidity (RH), non-condensing

Altitude

Maximum operating altitude: 15,000 feet (4,752 meters)

System

•The processor is a Motorola MPC875 series 32-bit PowerPC core, 133 MHz

•8 MB Flash

•32 MB SDRAM

Dimensions

1.75 inches (4.44 cm) height, standard 19-inch (48.26 cm) width, 12 inches (30.48 cm) depth

Weight and power dissipation

See table 12.

Table 12. SmartNode weight and maximum power specifications

SmartNode model	Weight	Maximum power dissipation

IpChannel Bank 4912	9.1 lb (4.1 kg)	25W
IpChannel Bank 4916	9.1 lb (4.1 kg)	30W

IpChannel Bank 4924	9.1 lb (4.1 kg)	40W

Management

59

Image 59

Patton electronic 4900 Management, Operating environment, System, Dimensions, Weight and power dissipation, Temperature

Contents

Sales Office +1 301 SmartNodeIpChannel Bank User Manual7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Hardware installation Table of ContentsSummary Table of Contents Table of Contents6 Contacting Patton for assistance Table of Contents4 Getting started with the SmartNode 4900 Series 5 LEDs status and monitoringE End user license agreement SpecificationsFactory Configuration Port pin-outsAccessories Table of ContentsWarranty Installation checklistList of Figures List of Tables Structure About this guideAudience Strictly follow the warning instructions to avoid personal injury Precautionsimpaired functioning Note A note presents additional information or interesting sidelightshas earth ground Safety when working with electricityThe Model SN4900 can only be configured with two AC power protected by a circuit breakerProtect the unit from moisture, vapors, and corrosive liquids Preventing Electrostatic Discharge DamageGeneral observations Clean the case with a soft slightly moist anti-static clothGaramond blue type Typographical conventions used in this documentGeneral conventions General information Chapter contentsChapter SmartNode 4900 Series overview SN4912/JO/RUI 12 FXO ports SN4916/JO/RUI 16 FXO ports SmartNode 4900 Series detailed descriptionSN4912/JSx/RUI 12 FXS ports SN4916/JSx/RUI 16 FXS ports SN4924/JSx/RUI 24 FXS ports SN4932/JSx/RUI 32 FXS portsDescription SmartNode 4900 Series front panelLED Condition Expansion port SmartNode 4900 Series rear panels1 General information Model SN4932Expansion Reset button behaviorChapter contents Chapter 2 Applications overviewSmartNode 4900 Series applications Multiservice carrier access over leased linesIntroduction Figure 6. Bulk analog line extensions application Enterprise FXS concentration and extension over IP and T1/E1Bulk analog line extensions Chapter Hardware installationChapter contents Introduction Planning the installationCreate a network diagram see section “Network information” on page Verify power source reliability see section “Power source” on pageSite log Installation checklistappendix F, “Installation checklist” on page Network information Network diagramConfiguration tools AC Power MainsUnpacking the Model SN4900 series IpChannel Bank Installing the IpChannel BankIpChannel Bank chassis installation Location and mounting requirementsConnecting the FXO ports Connecting cablesConnecting the FXS ports Figure 9. Cross-over RJ-45-to-RJ-45 Ethernet cable diagram Connecting the Ethernet portsX.21 interface DB-15 Connecting the EIA-561 RS-232 configuration port DCE configuredConnecting the serial port V.35 Interface DB-25Grounding the Model SN4900-AC and DC units Connecting powerInstalling the power cables-AC units 3. Repeat steps 1 and 2 to install the remaining power cable Installing the power cables-DC units3. Insert the stripped end of the positive lead into the +DC input of the terminal block. Tighten the screw until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the -DC input of the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires Chapter contents Chapter 4 Getting started with theSmartNode 4900 Series 4 Getting started with the SmartNode 4900 Series Figure 14. Connecting the SmartNode to your laptop PCFigure 15. Connecting the SmartNode to the network IntroductionFactory-default IP settings 1. Configure IP address8 bit 1 stop bit No flow control Connect to the RS-232 console portTerminal emulation program settings Asynchronous 9600 bps No parity e.g. HyperTermChanging the WAN IP address Login3. Loading the configuration optional 2. Connecting the SmartNode to the networkStart Bootloader BootloaderRedBoot fis load Start-up with factory configurationLoad a new application image SmartWare via TFTP CommandDownload it after starting up SmartWare with the following command Load a new application image SmartWare via the serial link Additional informationChapter contents Chapter 5 LEDs status and monitoring5 LEDs status and monitoring Status LEDsChapter contents Chapter 6 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationCE Declaration of Conformity Safety complianceCompliance Radio and TV interference FCC PartAuthorized European Representative Watchfield Swindon, Wilts SN6 8TD, UKA Compliance information FCC Part 68 ACTA Statement FXO ports FCC Part 68 ACTA Statement FXO portsIndustry Canada Notice FXO Ports Chapter contents Appendix B SpecificationsConsole port Voice connectivity - FXSVoice connectivity - FXO Ethernet interfacePPP and Frame-Relay support Voice processing signaling dependentFXS ports FXO portsVoice routing-session router Voice signalingIP services Management DimensionsWeight and power dissipation TemperatureDC version Power supplyIdentification of the SmartNode devices via SNMP Universal AC versionChapter contents Appendix C Port pin-outsFigure 19. EIA-561 RJ-45 8-pin port Ethernet 10Base-T and 100Base-T portIntroduction Console portSync Serial port Sync Serial portBlue FXS and FXO portsYellow BlueYellow GreenBlack BlackBlack BlackPair Chapter contents Appendix D Factory ConfigurationIntroduction D Factory ConfigurationIntroduction End User License Agreement Appendix E End user license agreementChapter contents Warranty2. Title 5. WarrantyEnd User License Agreement 1. Definitions7. Other licenses 6. TerminationChapter contents Appendix F Installation checklistIntroduction F Installation checklistChapter contents Appendix G AccessoriesPart Number IntroductionDescription