Manuals / Patton electronic / Computer Equipment / Network Hardware

Patton electronic 4900 Appendix E End user license agreement, Chapter contents, Definitions, Term

Models: 4900

1 76

Page 70

Appendix E End user license agreement
Chapter contents
End User License Agreement		70
1.	Definitions	70
2.	Title	70
3.	Term	70
4.	Grant of License	70
5.	Warranty	70
6.	Termination	71
7.	Other licenses	71

Page 70

Image 70

Contents

User Manual SmartNodeIpChannel Bank Sales Office +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Table of ContentsSummary Table of Contents Hardware installation5 LEDs status and monitoring Table of Contents4 Getting started with the SmartNode 4900 Series 6 Contacting Patton for assistancePort pin-outs SpecificationsFactory Configuration E End user license agreementInstallation checklist Table of ContentsWarranty AccessoriesList of Figures List of Tables Audience About this guideStructure Note A note presents additional information or interesting sidelights Precautionsimpaired functioning Strictly follow the warning instructions to avoid personal injuryprotected by a circuit breaker Safety when working with electricityThe Model SN4900 can only be configured with two AC power has earth groundClean the case with a soft slightly moist anti-static cloth Preventing Electrostatic Discharge DamageGeneral observations Protect the unit from moisture, vapors, and corrosive liquidsGeneral conventions Typographical conventions used in this documentGaramond blue type Chapter Chapter contentsGeneral information SmartNode 4900 Series overview SN4924/JSx/RUI 24 FXS ports SN4932/JSx/RUI 32 FXS ports SmartNode 4900 Series detailed descriptionSN4912/JSx/RUI 12 FXS ports SN4916/JSx/RUI 16 FXS ports SN4912/JO/RUI 12 FXO ports SN4916/JO/RUI 16 FXO portsLED Condition SmartNode 4900 Series front panelDescription Model SN4932 SmartNode 4900 Series rear panels1 General information Expansion portReset button behavior ExpansionChapter 2 Applications overview Chapter contentsIntroduction Multiservice carrier access over leased linesSmartNode 4900 Series applications Bulk analog line extensions Enterprise FXS concentration and extension over IP and T1/E1Figure 6. Bulk analog line extensions application Chapter contents Hardware installationChapter Verify power source reliability see section “Power source” on page Planning the installationCreate a network diagram see section “Network information” on page Introductionappendix F, “Installation checklist” on page Installation checklistSite log AC Power Mains Network diagramConfiguration tools Network informationLocation and mounting requirements Installing the IpChannel BankIpChannel Bank chassis installation Unpacking the Model SN4900 series IpChannel BankConnecting the FXS ports Connecting cablesConnecting the FXO ports Connecting the Ethernet ports Figure 9. Cross-over RJ-45-to-RJ-45 Ethernet cable diagramV.35 Interface DB-25 Connecting the EIA-561 RS-232 configuration port DCE configuredConnecting the serial port X.21 interface DB-15Connecting power Grounding the Model SN4900-AC and DC unitsInstalling the power cables-AC units Installing the power cables-DC units 3. Repeat steps 1 and 2 to install the remaining power cable3. Insert the stripped end of the positive lead into the +DC input of the terminal block. Tighten the screw until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the -DC input of the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires SmartNode 4900 Series Chapter 4 Getting started with theChapter contents Introduction Figure 14. Connecting the SmartNode to your laptop PCFigure 15. Connecting the SmartNode to the network 4 Getting started with the SmartNode 4900 Series1. Configure IP address Factory-default IP settingse.g. HyperTerm Connect to the RS-232 console portTerminal emulation program settings Asynchronous 9600 bps No parity 8 bit 1 stop bit No flow controlLogin Changing the WAN IP address2. Connecting the SmartNode to the network 3. Loading the configuration optionalBootloader Start BootloaderCommand Start-up with factory configurationLoad a new application image SmartWare via TFTP RedBoot fis loadDownload it after starting up SmartWare with the following command Additional information Load a new application image SmartWare via the serial linkChapter 5 LEDs status and monitoring Chapter contentsStatus LEDs 5 LEDs status and monitoringChapter 6 Contacting Patton for assistance Chapter contentsContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Patton support headquarters in the USAReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix A Compliance information Chapter contentsRadio and TV interference FCC Part Safety complianceCompliance CE Declaration of ConformityA Compliance information Watchfield Swindon, Wilts SN6 8TD, UKAuthorized European Representative Industry Canada Notice FXO Ports FCC Part 68 ACTA Statement FXO portsFCC Part 68 ACTA Statement FXO ports Appendix B Specifications Chapter contentsEthernet interface Voice connectivity - FXSVoice connectivity - FXO Console portFXO ports Voice processing signaling dependentFXS ports PPP and Frame-Relay supportIP services Voice signalingVoice routing-session router Management DimensionsWeight and power dissipation Operating environmentUniversal AC version Power supplyIdentification of the SmartNode devices via SNMP DC versionAppendix C Port pin-outs Chapter contentsConsole port Ethernet 10Base-T and 100Base-T portIntroduction Figure 19. EIA-561 RJ-45 8-pin portSync Serial port Sync Serial portFXS and FXO ports BlueGreen BlueYellow YellowBlack BlackBlack BlackPair Appendix D Factory Configuration Chapter contentsIntroduction D Factory ConfigurationIntroduction Warranty Appendix E End user license agreementChapter contents End User License Agreement1. Definitions 5. WarrantyEnd User License Agreement 2. Title6. Termination 7. Other licensesAppendix F Installation checklist Chapter contentsF Installation checklist IntroductionAppendix G Accessories Chapter contentsDescription IntroductionPart Number