Manuals / Paxar / Computer Equipment / Printer

Paxar TC6032EM manual Pinch and Feed Rollers, Platen Roller

Models: TC6032EM

1 40

Download 40 pages 53.01 Kb

Page 28

Platen

4. Use a dry, soft-bristle brush, such as a toothbrush, to clean either the standard (black) or linerless (red/orange textured) platen roller.

Platen

Roller

5. Turn the platen roller with your finger, and then continue cleaning.

6. Reload the supplies and close the label deflector and supply cover.

NOTE: DO NOT use alcohol or solvents on linerless (red/orange textured) platen rollers.

If the brush does not remove all the adhesive:

♦use isopropyl alcohol ONLY on the standard (black) platen roller. Moisten a cotton swab with isopropyl alcohol and run the cotton swab across the platen roller. Turn the platen roller with your finger to make sure the platen roller is clean all the way around. After cleaning, feed several inches of supply through without printing to remove any remaining isopropyl alcohol.

♦Call Service to clean the linerless (red/orange textured) platen roller.

Pinch and Feed Rollers

To clean the pinch and feed rollers:

1. Turn the printer off and open the supply cover.

2. Remove the supplies. See “Removing Supplies” in Chapter 3.

5-4 Care and Maintenance

Image 28

Paxar TC6032EM manual Pinch and Feed Rollers, Platen Roller

Contents

Silver Printer Monarchâ Pathfinderâ UltraâTC6032EM Rev. AE 2/03 2002 Paxar Corporation. All rights reserved RBRC is a trademark of Rechargeable Battery Recycling Corporation TrademarksPaxar is a trademark of Paxar Corporation Paxar Corporation 170 Monarch Lane Miamisburg, OHUsing Batteries Using SuppliesTA B L E O F C O N T E N T S IntroductionCare and Maintenance TroubleshootingGlossary Reference InformationI N T R O D U C T I O N G e t t i n g S t a r t e dU s i n g t h i s M a n u a l U S I N G B AT T E R I E S C h a r g i n g B a t t e r i e sBattery Battery Compartment Door ButtonC h a n g i n g B a t t e r i e s R e c y c l i n g B a t t e r i e s S a f e t y I n f o r m a t i o n2-4 Using Batteries U S I N G S U P P L I E S L o a d i n g S u p p l i e sCover Latch Buttons Supply Holder3. Press the latch buttons and open the supply cover 4. Open the spring-loaded supply holderLoading for Peel Mode Applicator Roller Peel Bar Label Deflector Label Deflector3-4 Using Supplies Guide Roller behind supply Feed Roller behind pinch Roller Pinch RollerLoading for Non - Peel Mode R e m o v i n g S u p p l i e sApplicator Roller Label Deflector B A S I C O P E R AT I O N S U s i n g t h e K e y p a dEntering Data Reading the Status Line U s i n g t h e D i s p l a yEntering Letters S c a n n i n g B a r C o d e s If the bar code does not scan C e r t i f i c a t i o n N o t e 4-6 Basic OperationsP o w e r M a n a g e m e n t P r i n t i n gA t t a c h i n g t h e S a f e t y S t r a p H e l p f u l R e m i n d e r s C A R E A N D M A I N T E N A N C E C l e a n i n gPrinthead Platen Roller PrintheadPinch and Feed Rollers Platen RollerScanner Window Black Mark SensorBlack Mark Sensor Scanner Flex Cable Adhesive Buildup Scanner Flex CableC l e a r i n g S u p p l y J a m s Pinch Roller Feed Roller is behind itDo Not store the printer in or near magnetic fields wet or damp areas S t o r i n g t h e P r i n t e rdirty or dusty areas areas of intense vibration or shock T R O U B L E S H O O T I N G Following are some common printer problems and their solutionsError Codes G L O S S A R YA To use this printer, you should be familiar with the following termsA-2 Glossary S p e c i f i c a t i o n s R E F E R E N C E I N F O R M AT I O NA c c e s s o r i e s / O p t i o n s 9462 Single-Station Battery Charger 9464 4-Station Battery ChargerAC Power Supply 110V - 240V-operating range is 95V Extra Battery Wrist Strap Available on our Web site