Adjusting the TREBLE, BASS, and Balance | Philips 55P8342, 64P8341

Sound Menu • Treble, Bass, and Balance

ADJUSTING THE TREBLE, BASS, AND BALANCE

Besides the normal volume level control, your TV also has individ-

ual sound-adjustment controls. You can use TREBLE (high frequency), BASS (low frequency), and Speaker BALANCE to further adjust the sound playback of TV programs.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN once to highlight SOUND.

Press the CURSOR RING

RIGHT to enter the SOUND menu.

Press the CURSOR RING RIGHT or LEFT to adjust the TRE- BLE level of the television’s sound.

After adjusting the TREBLE con-

trol, press the CURSOR RING

DOWN to select another sound adjustment: BASS or BALANCE.

Then Press the CURSOR RING RIGHT or LEFT to adjust the

selected control.

Press the STATUS/EXIT button

to remove the menu from the screen.

SMART HELP

Remember, when the bar scale is centered, speaker

sound BALANCE is centered between the TV’s left and right side speakers.

	PICTURE			TREBLE
	SOUND			BASS
	FEATURES			BALANCE			SOUND
	INSTALL			AVL			SOUND
	INSTALL			AVL			TREBLE		30
				INCR. SURROUND			TREBLE		30
				INCR. SURROUND			BASS
							BASS
							BALANCE
							AVL
							INCR. SURROUND
							SOUND
				POWER			TREBLE
							BASS		30
							BALANCE
							AVL
							INCR. SURROUND
	TV		VCR	ACC
	SWAP		PIP CH	SOURCE FREEZE		4
5		DN	UP		3	4	SOUND
		DN	UP				SOUND
	SOUND			PICTURE				TREBLE
6								BASS
6								BALANCE	0
	STATUS/			MENU/				AVL
	EXIT			SELECT				AVL
								INCR. SURROUND
			MUTE			1
	VOL			CH		1
		5		2
	1	5		3
	1			3
	4		5	6
	7		8	9
	TV/VCR		0
	A/CH		0	SURF
	POSITION			PIP

31

Image 31

Philips 55P8342, 64P8341, 64P8342, 50P8342, 50P 8341 Adjusting the TREBLE, BASS, and Balance, Trol, press the Cursor Ring

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV Features Screen menu Adjusting the PicturePress the Cursor Ring Right Press the STATUS/EXIT button Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the MENU/SELECT but Press the Cursor Ring Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Turning on the Imagemax Control Converge RED/BLUE Converge Multipoint RED/BLUE Right to enter Navigate modeDown repeatedly until MULTI- Point RED is selected Save Multipoint Press the MENU/SELECT but Ton to return to the ConvergenceMenu Multipoint RED Down repeatedly until Undo Multipoint is selected Undo MultipointUndo Multipoint Press the MENU/SELECT button Setting the ClockPress the Cursor Ring Down Down twice to highlight FEA Setting the Start TimeRight to enter the Features menu Right again to highlight the time indicator area Highlight the Stop Time control Setting the Stop TimeRight to highlight the time indica- tor area Enter the desired start-up channel. Or Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Press the Number buttons to Selecting the Tuner Tuner Mode Cursor Ring Right again Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR ONCE, press the Cursor Ring Constantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFF Movie Ratings Understanding Autolock Enter your new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter a new four-digit code Blocking Channels Enter your four-digit AccessPress the Cursor Ring UP or Down repeatedly until Movie Rating is highlighted Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Blocking by Movie Rating ING is highlighted Blocking by TV RatingRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor Ring Right to enter the Block Options menu Blocking Unrated BroadcastsDown once to select Block Press the Cursor Ring Right or Left to turn no RAT Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Down twice to highlight no RAT- ING Them from the screen Reviewing Your SettingsPress the STATUS/EXIT but STATUS/EXIT button to remove Right again to highlight Clearing ALL Blocked Channels SOR Ring Right again to high Using the Closed Captioning ControlDown to select a Caption Mode Down repeatedly until the Closed CAP control is highlighted Then Press the Cursor Ring Right or Left to adjust Adjusting the TREBLE, BASS, and BalanceTrol, press the Cursor Ring Down repeatedly until AVL is high Using the AVL Audio Volume Leveler ControlOn or OFF Mono Using Incredible Surround Treble Setting the TV for Stereo and SAPDown once to highlight Sound menu Sound Or Right to set the Audio OUT to Variable or Fixed Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Press the Cursor Ring Left To hear the TV sound from only the audio system speakers Using the TV Speaker Control and Audio OutputsTon to remove the menu from the screen Using the Bass Boost Control Press the Picture button on Using AutopicturePress the Picture button AutoSound Choices Using AutosoundPress the Sound button on the remote control. The current AutoSound setting will appear in the middle of the screen Surf Using SURF, Alternate CHANNEL, and Program List Sleep OFF Using the Sleep Timer ControlSleep Volume Using the Volume ButtonsPress the VOLume +,- but Tons to adjust the TV’s sound level CV1 TUNER-B TUNER-A Using the AV Button Desired accessory device and press the Power button Setting the TV Remote to Work Accessory DevicesDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search Method See the next page for more codes Setting the TV Remote to Work Accessories Satellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic Connections Buttons to change channels in the PIP window Selecting the PIP Signal SourceInput on the back of the TV, you Can press the PIP CHannel DN/UP To remove PIP from the screen Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to Show the PIP window again Press the Cursor Ring Right to enter the Features Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Down twice to highlight FEA Connect a cable TV signal to a Using Connection OptionsConnect the other RF coaxial Cable to the INput on the cable box Connect two RF coaxial cables toUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service Locations Houston Projection Television Limited Warranty