Using the AVL Audio Volume Leveler Control | Philips 64P8341

Sound Menu • AVL (Audio Volume Leveler)

USING THE AVL (AUDIO VOLUME LEVELER) CONTROL

You may have noticed the peaks and valleys of sound that occur

between program changes or at com- mercial breaks. The volume levels often vary considerably. By turning ON the AVL (Audio Volume Leveler) control, you can make your TV pro- duce a more consistent volume level. Follow these steps to turn the AVL ON.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN once to highlight SOUND.

Press the CURSOR RING

RIGHT to enter the SOUND menu.

Press the CURSOR RING

DOWN repeatedly until AVL is high-

lighted. Then press the CURSOR RING RIGHT or LEFT to turn AVL

ON or OFF.

Press the STATUS/EXIT button

to remove the menu from the screen.

		PICTURE			TREBLE
		SOUND			BASS
		FEATURES			BALANCE		SOUND
		INSTALL			AVL		SOUND
		INSTALL			AVL		TREBLE	30
					INCR. SURROUND		TREBLE	30
					INCR. SURROUND		BASS
							BASS
							BALANCE
							AVL
							INCR. SURROUND
							SOUND
					POWER		TREBLE
							BASS
							BALANCE
							AVL	OFF
							INCR. SURROUND
		TV		VCR	ACC
		SWAP		PIP CH	SOURCE FREEZE
			DN	UP		3	OR
	4	SOUND			PICTURE		OR
		SOUND			PICTURE
5							AVL	ON
5		STATUS/			MENU/
		EXIT			SELECT
				MUTE			1
		VOL			CH
			4		2
		1	4		3
		1			3

4 5 6

7 8 9

TV/VCR

A/CH	0	SURF
POSITION		PIP

32

Image 32

Philips 64P8341, 64P8342, 50P8342 Using the AVL Audio Volume Leveler Control, Down repeatedly until AVL is high, On or OFF

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TV Press the Cursor Ring Right Adjusting the PictureScreen menu Press the Cursor Ring Right or Left to switch DNR on Turning on the Dynamic Noise Reduction DNR ControlPress the MENU/SELECT but Press the STATUS/EXIT button Ton on the remote control to show the on-screen menu Right or LEFTto switch between on and OFFTurning on the Imagemax Control Press the Cursor Ring Converge RED/BLUE Down repeatedly until MULTI- Point RED is selected Right to enter Navigate modeConverge Multipoint RED/BLUE Press the MENU/SELECT but Ton to return to the Convergence MenuMultipoint RED Save Multipoint Undo Multipoint Undo MultipointDown repeatedly until Undo Multipoint is selected Press the Cursor Ring Down Setting the ClockPress the MENU/SELECT button Setting the Start Time Right to enter the Features menuRight again to highlight the time indicator area Down twice to highlight FEA Right to highlight the time indica- tor area Setting the Stop TimeHighlight the Stop Time control Selecting the Channel Press the Cursor Ring RIGHT. Then press the CursorPress the Number buttons to Enter the desired start-up channel. Or Tuner Mode Selecting the Tuner Setting the Activate Control Press the Cursor Ring Right again. Then press the CURONCE, press the Cursor Ring Cursor Ring Right again Right or Left to turn the Timer Display on or OFF Constantly Displaying the Time on Screen Understanding Autolock Movie Ratings Setting UP the Access Code Press the Cursor Ring Right to highlight AccessEnter a new four-digit code Enter your new four-digit code Press the Cursor Ring UP or Enter your four-digit AccessBlocking Channels Right again to highlight Access Enter your four-digit Access CODE. Correct will flash veryBlocking by Movie Rating Down repeatedly until Movie Rating is highlighted Right to enter the TV Rating menu Blocking by TV RatingING is highlighted Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFF Down once to select Block Blocking Unrated BroadcastsRight to enter the Block Options menu Right again to highlight Access Code input area Blocking Broadcasts That have no RatingDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RAT Reviewing Your Settings Press the STATUS/EXIT butSTATUS/EXIT button to remove Them from the screen Clearing ALL Blocked Channels Right again to highlight Using the Closed Captioning Control Down to select a Caption ModeDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to high Trol, press the Cursor Ring Adjusting the TREBLE, BASS, and BalanceThen Press the Cursor Ring Right or Left to adjust On or OFF Using the AVL Audio Volume Leveler ControlDown repeatedly until AVL is high Using Incredible Surround Mono Setting the TV for Stereo and SAP Down once to highlight Sound menuSound Treble Setting the Audio OUT Control Down repeatedly until Audio OUT is highlightedPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or Fixed Ton to remove the menu from the screen Using the TV Speaker Control and Audio OutputsTo hear the TV sound from only the audio system speakers Using the Bass Boost Control Press the Picture button Using AutopicturePress the Picture button on Using Autosound Press the Sound button on the remote control. The currentAutoSound setting will appear in the middle of the screen AutoSound Choices Using SURF, Alternate CHANNEL, and Program List Surf Sleep Using the Sleep Timer ControlSleep OFF Using the Volume Buttons Press the VOLume +,- butTons to adjust the TV’s sound level Volume Using the AV Button CV1 TUNER-B TUNER-A Does the remote turn the accessory device on? Setting the TV Remote to Work Accessory DevicesDesired accessory device and press the Power button Please read through all the steps before beginning Search Method Ry device and continue holding the buttons down Setting the TV Remote to Work Accessories See the next page for more codes Satellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Selecting the PIP Signal Source Input on the back of the TV, youCan press the PIP CHannel DN/UP Buttons to change channels in the PIP window Using the PIP Remote Control Buttons Press the PIP ON/OFF button toShow the PIP window again To remove PIP from the screen Press the Cursor Ring Down twice to highlight FEA Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Right to enter the Features Connect the other RF coaxial Using Connection OptionsConnect a cable TV signal to a Use another RF coaxial cable to Connect two RF coaxial cables toCable to the INput on the cable box Helpful Hints Glossary of Television Terms Index Factory Service Locations Canada Houston Limited Warranty Projection Television