Setting the Activate Control | Philips 50P8342, 64P8341, 64P8342

Features Menu • The Timer Control

11	12	1
10		2
9		3
8		4

75

6

SETTING THE ACTIVATE CONTROL

After you have set the Time, Start Time, Stop Time, and Start

Channel, you must activate the Timer for it to operate. Your options are to set the Timer to work ONCE or DAILY. Set ACTIVATE to OFF if you don’t want to use the Timer.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN twice to highlight FEA-

TURES.

Press the CURSOR RING

RIGHT to enter the FEATURES menu.

Press the CURSOR RING RIGHT again. Then press the CUR-

SOR RING DOWN repeatedly until the ACTIVATE control is highlighted.

Press the CURSOR RING

RIGHT again to set ACTIVATE to

ONCE, press the CURSOR RING

RIGHT again for DAILY, or press

the CURSOR RING RIGHT again

to toggle ACTIVATE to OFF.

Press the STATUS/EXIT button

to remove the menu from the screen.

SMART HELP

Before you set the TIMER controls, you must

set the TV’s clock manually with- in the Timer menu (see page 13) or by using the AutoChron feature described on page 6 of the Setup and Quick Use Guide.

Try it! After following the steps on pages 13–19, use your TV to wake you up like a clock radio.

6

PICTURE			TIMER
SOUND			AUTOLOCK
FEATURES			PIP			FEATURES
INSTALL			CLOSED CAP			FEATURES
INSTALL			CLOSED CAP			TIMER	TIME
						TIMER	TIME
						AUTOLOCK	START TIME
						PIP	STOP TIME
						CLOSED CAP	CHANNEL
							TUNER MODE
						FEATURES
			POWER			TIMER
						TIME		8:05 PM
						START TIME
						STOP TIME
						CHANNEL
TV		VCR	ACC			TUNER MODE
TV		VCR	ACC			5
SWAP		PIP CH	SOURCE FREEZE		4	5
	DN	UP		3	4	FEATURES
						FEATURES
SOUND			PICTURE			TIMER
						TIMER
							START TIME
STATUS/			MENU/				STOP TIME
STATUS/			MENU/
EXIT			SELECT				CHANNEL
							CHANNEL
							TUNER MODE
					1		ACTIVATE	OFF
		MUTE
VOL			CH
		2					OR
	4						OR
1	4		3				ACTIVATE	ONCE
1			3				ACTIVATE	ONCE
4		5	6				OR
7		8	9				ACTIVATE	DAILY
TV/VCR		0
A/CH		0	SURF
POSITION			PIP

18

Image 18

Philips 50P8342, 64P8341, 64P8342 manual Setting the Activate Control, Press the Cursor Ring Right again. Then press the CUR

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TV Adjusting the Picture Screen menuPress the Cursor Ring Right Press the MENU/SELECT but Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the STATUS/EXIT button Turning on the Imagemax Control Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Press the Cursor Ring Converge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Multipoint RED Press the MENU/SELECT but Ton to return to the ConvergenceMenu Save Multipoint Undo Multipoint Down repeatedly until Undo Multipoint is selectedUndo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Right again to highlight the time indicator area Setting the Start TimeRight to enter the Features menu Down twice to highlight FEA Setting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Press the Number buttons to Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Enter the desired start-up channel. Or Tuner Mode Selecting the Tuner ONCE, press the Cursor Ring Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR Cursor Ring Right again Right or Left to turn the Timer Display on or OFF Constantly Displaying the Time on Screen Understanding Autolock Movie Ratings Enter a new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter your new four-digit code Enter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Blocking by Movie Rating Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Down repeatedly until Movie Rating is highlighted Blocking by TV Rating ING is highlightedRight to enter the TV Rating menu Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFF Blocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Down twice to highlight no RAT- ING Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Press the Cursor Ring Right or Left to turn no RAT STATUS/EXIT button to remove Reviewing Your SettingsPress the STATUS/EXIT but Them from the screen Clearing ALL Blocked Channels Right again to highlight Down repeatedly until the Closed CAP control is highlighted Using the Closed Captioning ControlDown to select a Caption Mode SOR Ring Right again to high Adjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Using Incredible Surround Mono Sound Setting the TV for Stereo and SAPDown once to highlight Sound menu Treble Press the Cursor Ring Left Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Or Right to set the Audio OUT to Variable or Fixed Using the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button AutoSound setting will appear in the middle of the screen Using AutosoundPress the Sound button on the remote control. The current AutoSound Choices Using SURF, Alternate CHANNEL, and Program List Surf Using the Sleep Timer Control Sleep OFFSleep Tons to adjust the TV’s sound level Using the Volume ButtonsPress the VOLume +,- but Volume Using the AV Button CV1 TUNER-B TUNER-A Setting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Search Method Ry device and continue holding the buttons down Setting the TV Remote to Work Accessories See the next page for more codes Satellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Can press the PIP CHannel DN/UP Selecting the PIP Signal SourceInput on the back of the TV, you Buttons to change channels in the PIP window Show the PIP window again Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to To remove PIP from the screen Adjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Factory Service Locations Canada Houston Limited Warranty Projection Television