Manuals / Philips / TV and Video / Projection Television

Philips 50P 8341 Setting the Audio OUT Control, Down repeatedly until Audio OUT is highlighted

Models: 50P 8341 55P 8341 64P8341 60P8342 60P 8341 50P8342 64P8342 55P8342

1 60

Download 60 pages 11.1 Kb

Page 35

Sound Menu • The Audio Out Control

SETTING THE AUDIO OUT CONTROL

If you have connected the TV’s AUDIO OUTPUT jacks to the AUDIO INPUT jacks on a stereo

receiver, set AUDIO OUT to either VARIABLE or FIXED to determine whether you adjust the volume at the at the TV or at the stereo. If you select VARIABLE, change the volume at the TV using the TV’s remote control. If you select FIXED, adjust the volume at the stereo using the stereo’s con- trols. Follow these steps to make your selection.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING DOWN once to highlight SOUND.

Press the CURSOR RING RIGHT to enter the SOUND menu.

Press the CURSOR RING

DOWN repeatedly until AUDIO

OUT is highlighted.

Press the CURSOR RING LEFT

or RIGHT to set the AUDIO OUT to VARIABLE or FIXED.

Press the STATUS/EXIT button

to remove the menu from the screen.

	PICTURE		TREBLE
	SOUND		BASS
	FEATURES		BALANCE		SOUND
	INSTALL		AVL		SOUND
	INSTALL		AVL		TREBLE	30
			INCR. SURROUND		TREBLE	30
			INCR. SURROUND		BASS
					BASS
					BALANCE
					AVL
					INCR. SURROUND
					SOUND
			POWER		AVL
					AVL
					INCR. SURROUND
					STEREO
					SAP
					AUDIO OUT	FIXED
	TV	VCR	ACC
	SWAP	PIP CH	SOURCE FREEZE
5	DN	UP		3
5	SOUND		PICTURE	3		OR
6					SOUND
	STATUS/		MENU/		SOUND
	EXIT		SELECT
					AVL
				1	INCR. SURROUND
		MUTE			STEREO
	VOL		CH		SAP
		2			AUDIO OUT	VARIABLE
		2
	4		3
	4	5	6
	7	8	9
	TV/VCR	0
	A/CH	0	SURF
	POSITION		PIP

35

Image 35

Philips 50P 8341 Setting the Audio OUT Control, Down repeatedly until Audio OUT is highlighted, Press the Cursor Ring Left

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesPress the Cursor Ring Right Adjusting the PictureScreen menu Press the STATUS/EXIT button Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the MENU/SELECT butPress the Cursor Ring Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Turning on the Imagemax ControlConverge RED/BLUE Down repeatedly until MULTI- Point RED is selected Right to enter Navigate modeConverge Multipoint RED/BLUE Save Multipoint Press the MENU/SELECT but Ton to return to the ConvergenceMenu Multipoint REDUndo Multipoint Undo MultipointDown repeatedly until Undo Multipoint is selected Press the Cursor Ring Down Setting the ClockPress the MENU/SELECT button Down twice to highlight FEA Setting the Start TimeRight to enter the Features menu Right again to highlight the time indicator areaRight to highlight the time indica- tor area Setting the Stop TimeHighlight the Stop Time control Enter the desired start-up channel. Or Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Press the Number buttons toSelecting the Tuner Tuner ModeCursor Ring Right again Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR ONCE, press the Cursor RingConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockEnter your new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter a new four-digit codePress the Cursor Ring UP or Enter your four-digit AccessBlocking Channels Down repeatedly until Movie Rating is highlighted Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Blocking by Movie RatingRight to enter the TV Rating menu Blocking by TV RatingING is highlighted Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingDown once to select Block Blocking Unrated BroadcastsRight to enter the Block Options menu Press the Cursor Ring Right or Left to turn no RAT Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Down twice to highlight no RAT- INGThem from the screen Reviewing Your SettingsPress the STATUS/EXIT but STATUS/EXIT button to removeRight again to highlight Clearing ALL Blocked ChannelsSOR Ring Right again to high Using the Closed Captioning ControlDown to select a Caption Mode Down repeatedly until the Closed CAP control is highlightedTrol, press the Cursor Ring Adjusting the TREBLE, BASS, and BalanceThen Press the Cursor Ring Right or Left to adjust On or OFF Using the AVL Audio Volume Leveler ControlDown repeatedly until AVL is high Mono Using Incredible SurroundTreble Setting the TV for Stereo and SAPDown once to highlight Sound menu SoundOr Right to set the Audio OUT to Variable or Fixed Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Press the Cursor Ring LeftTon to remove the menu from the screen Using the TV Speaker Control and Audio OutputsTo hear the TV sound from only the audio system speakers Using the Bass Boost Control Press the Picture button Using AutopicturePress the Picture button on AutoSound Choices Using AutosoundPress the Sound button on the remote control. The current AutoSound setting will appear in the middle of the screenSurf Using SURF, Alternate CHANNEL, and Program ListSleep Using the Sleep Timer ControlSleep OFF Volume Using the Volume ButtonsPress the VOLume +,- but Tons to adjust the TV’s sound levelCV1 TUNER-B TUNER-A Using the AV ButtonDoes the remote turn the accessory device on? Setting the TV Remote to Work Accessory DevicesDesired accessory device and press the Power button Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsButtons to change channels in the PIP window Selecting the PIP Signal SourceInput on the back of the TV, you Can press the PIP CHannel DN/UPTo remove PIP from the screen Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to Show the PIP window againPress the Cursor Ring Down twice to highlight FEA Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Right to enter the Features Connect the other RF coaxial Using Connection OptionsConnect a cable TV signal to a Use another RF coaxial cable to Connect two RF coaxial cables toCable to the INput on the cable box Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty