Manuals / Philips / TV and Video / Projection Television

Philips 55P 8341, 64P8341, 64P8342, 50P8342, 50P 8341, 60P8342, 60P 8341 Using the Bass Boost Control

Models: 50P 8341 55P 8341 64P8341 60P8342 60P 8341 50P8342 64P8342 55P8342

1 60

Download 60 pages 11.1 Kb

Page 37

Sound Menu • The Bass Boost Control

USING THE BASS BOOST CONTROL

The BASS BOOST control allows you to increase the low-frequency

range of the TV’s sound. This creates a deeper, fuller sound. Follow these steps to turn BASS BOOST ON.

BEGIN

Press MENU/SELECT button on the remote control to show the on- screen menu.

Press the CURSOR RING

DOWN once to highlight SOUND.

Press the CURSOR RING

RIGHT to enter the SOUND menu.

Press the CURSOR RING DOWN repeatedly until BASS BOOST is highlighted.

Press the CURSOR RING RIGHT or LEFT to turn BASS BOOST ON or OFF.

Press the STATUS/EXIT button

to remove the menu from the screen.

	PICTURE			TREBLE
	SOUND			BASS
	FEATURES			BALANCE	SOUND
	INSTALL			AVL	SOUND
	INSTALL			AVL	TREBLE	30
				INCR. SURROUND	TREBLE	30
				INCR. SURROUND	BASS
					BASS
					BALANCE
					AVL
					INCR. SURROUND
					SOUND
				POWER	STEREO
					STEREO
					SAP
					AUDIO OUT
					SPEAKERS
					BASS BOOST	ON
	TV		VCR	ACC
	SWAP		PIP CH	SOURCE FREEZE
5		DN	UP		3	OR
	SOUND			PICTURE		OR
	SOUND			PICTURE		OFF
					BASS BOOST	OFF
	STATUS/			MENU/
	EXIT			SELECT
			MUTE		1
	VOL			CH
			2
	1	4		3
	1			3
	4		5	6
	7		8	9
	TV/VCR		0
	A/CH		0	SURF
	POSITION			PIP

37

Image 37

Philips 55P 8341, 64P8341, 64P8342, 50P8342, 50P 8341, 60P8342, 60P 8341, 55P8342 manual Using the Bass Boost Control

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesScreen menu Adjusting the PicturePress the Cursor Ring Right Turning on the Dynamic Noise Reduction DNR Control Press the Cursor Ring Right or Left to switch DNR onPress the MENU/SELECT but Press the STATUS/EXIT buttonRight or LEFTto switch between on and OFF Ton on the remote control to show the on-screen menuTurning on the Imagemax Control Press the Cursor RingConverge RED/BLUE Converge Multipoint RED/BLUE Right to enter Navigate modeDown repeatedly until MULTI- Point RED is selected Menu Press the MENU/SELECT but Ton to return to the ConvergenceMultipoint RED Save MultipointDown repeatedly until Undo Multipoint is selected Undo MultipointUndo Multipoint Press the MENU/SELECT button Setting the ClockPress the Cursor Ring Down Right to enter the Features menu Setting the Start TimeRight again to highlight the time indicator area Down twice to highlight FEAHighlight the Stop Time control Setting the Stop TimeRight to highlight the time indica- tor area Press the Cursor Ring RIGHT. Then press the Cursor Selecting the ChannelPress the Number buttons to Enter the desired start-up channel. OrSelecting the Tuner Tuner ModePress the Cursor Ring Right again. Then press the CUR Setting the Activate ControlONCE, press the Cursor Ring Cursor Ring Right againConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockPress the Cursor Ring Right to highlight Access Setting UP the Access CodeEnter a new four-digit code Enter your new four-digit codeBlocking Channels Enter your four-digit AccessPress the Cursor Ring UP or Enter your four-digit Access CODE. Correct will flash very Right again to highlight AccessBlocking by Movie Rating Down repeatedly until Movie Rating is highlightedING is highlighted Blocking by TV RatingRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingRight to enter the Block Options menu Blocking Unrated BroadcastsDown once to select Block Blocking Broadcasts That have no Rating Right again to highlight Access Code input areaDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RATPress the STATUS/EXIT but Reviewing Your SettingsSTATUS/EXIT button to remove Them from the screenRight again to highlight Clearing ALL Blocked ChannelsDown to select a Caption Mode Using the Closed Captioning ControlDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to highThen Press the Cursor Ring Right or Left to adjust Adjusting the TREBLE, BASS, and BalanceTrol, press the Cursor Ring Down repeatedly until AVL is high Using the AVL Audio Volume Leveler ControlOn or OFF Mono Using Incredible SurroundDown once to highlight Sound menu Setting the TV for Stereo and SAPSound TrebleDown repeatedly until Audio OUT is highlighted Setting the Audio OUT ControlPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or FixedTo hear the TV sound from only the audio system speakers Using the TV Speaker Control and Audio OutputsTon to remove the menu from the screen Using the Bass Boost Control Press the Picture button on Using AutopicturePress the Picture button Press the Sound button on the remote control. The current Using AutosoundAutoSound setting will appear in the middle of the screen AutoSound ChoicesSurf Using SURF, Alternate CHANNEL, and Program ListSleep OFF Using the Sleep Timer ControlSleep Press the VOLume +,- but Using the Volume ButtonsTons to adjust the TV’s sound level VolumeCV1 TUNER-B TUNER-A Using the AV ButtonDesired accessory device and press the Power button Setting the TV Remote to Work Accessory DevicesDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsInput on the back of the TV, you Selecting the PIP Signal SourceCan press the PIP CHannel DN/UP Buttons to change channels in the PIP windowPress the PIP ON/OFF button to Using the PIP Remote Control ButtonsShow the PIP window again To remove PIP from the screenPress the Cursor Ring Right to enter the Features Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Down twice to highlight FEA Connect a cable TV signal to a Using Connection OptionsConnect the other RF coaxial Cable to the INput on the cable box Connect two RF coaxial cables toUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty