Philips 55P 8341, 64P8341, 64P8342, 50P8342, 50P 8341, 60P8342, 55P8342

Remote Control • Working Accessory Devices

SETTING THE TV REMOTE TO WORK ACCESSORY DEVICES

DIRECT ACCESS METHOD

Now that you have looked up the three-digit Remote Control Direct

Entry Code for your brand of acces- sory device, you are ready to follow the simple steps shown below.

Please read through all the steps before beginning.

BEGIN

First, press and hold down the VCR or ACC (for an accessory device other than a VCR) mode button on the TV remote. Then press and hold down the MENU/SELECT button at the same time for a brief moment. Release the buttons. The TV remote back light will switch on.

Within 30 seconds of pressing the VCR (or ACC) button and MENU/SELECT button, enter a three-digit code for the accessory device (see pages 47 and 48).

Point the remote at the accessory device. Then press the POWER but- ton on the remote to turn the device on.

Satellite

Receiver

Cable TV

Converter

DVD

VCR

3

	POWER
TV
OK	VCR
SWAP		ACC
PIPCH		SOURCE
DN	UP	SOURCE	FREEZE
DN	UP		FREEZE
	UP
SOUND
			PICTURE
STATUS/
EXIT
				MENU/
				SELECT
	VOL		MUTE
	VOL
					CH
		1	2		3
			2
		4
		4		5		6
				5
			7
			7	8		9
			TV/VCR	8
			TV/VCR
			A/CH
			A/CH	0
				0		SURF
						CC
				POSITION
						PIP

POWER

TV	VCR	ACC
SWAP	PIP CH	SOURCE FREEZE
DN	UP
SOUND		PICTURE
STATUS/		MENU/
EXIT		SELECT
	MUTE
VOL		CH

1 2 3

4 5 6

7 8 9

TV/VCR

A/CH	0	SURF
POSITION		PIP

1

1

2

SMART HELP

• Pressing the ACC(esso- ry) mode button allows access to the product codes for accessory

devices.

•If the procedure explained above does not work the first time, repeat the steps using the same remote code number.

•If after a second try the remote does not operate your accessory device, and more code numbers are listed for your brand, use the next listed code number.

•If after repeated attempts the Direct Access Method does not allow you to work your accessory device with your TV remote, try the Search Method explained on the next page.

NOTES:

•If you do not enter a complete code within 30 seconds, you will need to perform step 1 of the Direct Access Method again.

•If you enter more than three digits, the unit will retain the first three digits entered.

45

Image 45

Philips 55P 8341, 64P8341, 64P8342, 50P8342, 50P 8341, 60P8342, 60P 8341 Please read through all the steps before beginning

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV Features Adjusting the Picture Screen menuPress the Cursor Ring Right Turning on the Dynamic Noise Reduction DNR Control Press the Cursor Ring Right or Left to switch DNR onPress the MENU/SELECT but Press the STATUS/EXIT button Right or LEFTto switch between on and OFF Ton on the remote control to show the on-screen menuTurning on the Imagemax Control Press the Cursor Ring Converge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Menu Press the MENU/SELECT but Ton to return to the ConvergenceMultipoint RED Save Multipoint Undo Multipoint Down repeatedly until Undo Multipoint is selectedUndo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Right to enter the Features menu Setting the Start TimeRight again to highlight the time indicator area Down twice to highlight FEA Setting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Press the Cursor Ring RIGHT. Then press the Cursor Selecting the ChannelPress the Number buttons to Enter the desired start-up channel. Or Selecting the Tuner Tuner Mode Press the Cursor Ring Right again. Then press the CUR Setting the Activate ControlONCE, press the Cursor Ring Cursor Ring Right again Constantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFF Movie Ratings Understanding Autolock Press the Cursor Ring Right to highlight Access Setting UP the Access CodeEnter a new four-digit code Enter your new four-digit code Enter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Enter your four-digit Access CODE. Correct will flash very Right again to highlight AccessBlocking by Movie Rating Down repeatedly until Movie Rating is highlighted Blocking by TV Rating ING is highlightedRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor Ring Blocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Blocking Broadcasts That have no Rating Right again to highlight Access Code input areaDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RAT Press the STATUS/EXIT but Reviewing Your SettingsSTATUS/EXIT button to remove Them from the screen Right again to highlight Clearing ALL Blocked Channels Down to select a Caption Mode Using the Closed Captioning ControlDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to high Adjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Mono Using Incredible Surround Down once to highlight Sound menu Setting the TV for Stereo and SAPSound Treble Down repeatedly until Audio OUT is highlighted Setting the Audio OUT ControlPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or Fixed Using the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button Press the Sound button on the remote control. The current Using AutosoundAutoSound setting will appear in the middle of the screen AutoSound Choices Surf Using SURF, Alternate CHANNEL, and Program List Using the Sleep Timer Control Sleep OFFSleep Press the VOLume +,- but Using the Volume ButtonsTons to adjust the TV’s sound level Volume CV1 TUNER-B TUNER-A Using the AV Button Setting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search Method See the next page for more codes Setting the TV Remote to Work Accessories Satellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic Connections Input on the back of the TV, you Selecting the PIP Signal SourceCan press the PIP CHannel DN/UP Buttons to change channels in the PIP window Press the PIP ON/OFF button to Using the PIP Remote Control ButtonsShow the PIP window again To remove PIP from the screen Adjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service Locations Houston Projection Television Limited Warranty