Adjusting the Picture, Screen menu | Philips 60P 8341, 64P8341

Picture Menu • Adjusting the Picture

To adjust your TV picture controls, select a channel and follow these

steps.

BEGIN

Press the MENU/SELECT button on the remote control to show the on-

screen menu.

ADJUSTING THE PICTURE

Press the CURSOR RING RIGHT.

BRIGHTNESS will be highlighted and an adjustment bar will be shown to the right.

Press the CURSOR RING RIGHT or LEFT to adjust the BRIGHTNESS level of the picture. Or press the CUR-

SOR RING DOWN to select another picture control to adjust.

Press the STATUS/EXIT button to remove the menu from the screen.

SMART HELP

When the bar scale

is centered, the

control settings are at normal, mid- range levels. Picture adjustment con- trols are described here.

BRIGHTNESS—adds or subtracts light from the darkest part of the picture.

COLOR—adds or eliminates color.

PICTURE—improves the detail of the lightest parts of the picture.

SHARPNESS—improves the detail in the picture.

TINT—adjusts the picture to obtain natural skin tones.

COLOR TEMP—offers NOR- MAL, COOL, or WARM picture preferences.

NORMAL—keeps whites, white.

COOL—makes whites, bluish.

WARM—makes whites, reddish.

		BRIGHTNESS
	PICTURE	BRIGHTNESS
	SOUND	COLOR
	FEATURES	PICTURE
	INSTALL	SHARPNESS
		TINT

POWER

	TV	VCR	ACC
	SWAP	PIP CH	SOURCE FREEZE		3
	DN	UP		2	3
	SOUND		PICTURE	2
	STATUS/		MENU/
	EXIT		SELECT
4		MUTE			1
4	VOL		CH		1
		3
	1	2	3
	4	5	6
	7	8	9
	TV/VCR	0
	A/CH	0	SURF
	POSITION		PIP

PICTURE
BRIGHTNESS	30

COLOR

PICTURE

SHARPNESS

STORE

PICTURE

BRIGHTNESS

COLOR 30

PICTURE

SHARPNESS

STORE

PICTURE

BRIGHTNESS

COLOR

PICTURE 30

SHARPNESS

STORE

PICTURE
	BRIGHTNESS
	COLOR
	PICTURE
	SHARPNESS			30
	TINT
	PICTURE
		BRIGHTNESS
		COLOR
		PICTURE
		SHARPNESS
		TINT		0
		PICTURE
			COLOR
			PICTURE
			SHARPNESS
			TINT
			COLOR TEMP	NORMAL
				OR
			COLOR TEMP	WARM
				OR
			COLOR TEMP	COOL

6

Image 6

Philips 60P 8341, 64P8341, 64P8342, 50P8342, 50P 8341, 60P8342 Adjusting the Picture, Screen menu, Press the Cursor Ring Right

Contents

Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TV Adjusting the Picture Screen menuPress the Cursor Ring Right Press the MENU/SELECT but Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the STATUS/EXIT button Turning on the Imagemax Control Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Press the Cursor Ring Converge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Multipoint RED Press the MENU/SELECT but Ton to return to the ConvergenceMenu Save Multipoint Undo Multipoint Down repeatedly until Undo Multipoint is selectedUndo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Right again to highlight the time indicator area Setting the Start TimeRight to enter the Features menu Down twice to highlight FEA Setting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Press the Number buttons to Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Enter the desired start-up channel. Or Tuner Mode Selecting the Tuner ONCE, press the Cursor Ring Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR Cursor Ring Right again Right or Left to turn the Timer Display on or OFF Constantly Displaying the Time on Screen Understanding Autolock Movie Ratings Enter a new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter your new four-digit code Enter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Blocking by Movie Rating Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Down repeatedly until Movie Rating is highlighted Blocking by TV Rating ING is highlightedRight to enter the TV Rating menu Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFF Blocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Down twice to highlight no RAT- ING Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Press the Cursor Ring Right or Left to turn no RAT STATUS/EXIT button to remove Reviewing Your SettingsPress the STATUS/EXIT but Them from the screen Clearing ALL Blocked Channels Right again to highlight Down repeatedly until the Closed CAP control is highlighted Using the Closed Captioning ControlDown to select a Caption Mode SOR Ring Right again to high Adjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Using Incredible Surround Mono Sound Setting the TV for Stereo and SAPDown once to highlight Sound menu Treble Press the Cursor Ring Left Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Or Right to set the Audio OUT to Variable or Fixed Using the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button AutoSound setting will appear in the middle of the screen Using AutosoundPress the Sound button on the remote control. The current AutoSound Choices Using SURF, Alternate CHANNEL, and Program List Surf Using the Sleep Timer Control Sleep OFFSleep Tons to adjust the TV’s sound level Using the Volume ButtonsPress the VOLume +,- but Volume Using the AV Button CV1 TUNER-B TUNER-A Setting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Search Method Ry device and continue holding the buttons down Setting the TV Remote to Work Accessories See the next page for more codes Satellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Can press the PIP CHannel DN/UP Selecting the PIP Signal SourceInput on the back of the TV, you Buttons to change channels in the PIP window Show the PIP window again Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to To remove PIP from the screen Adjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Factory Service Locations Canada Houston Limited Warranty Projection Television