Philips 765 manual Preparing for analogue recording, Stop the source, Start analogue recording

English

RECORDING

•To check the (remaining) recording time, press DISPLAY. (This can also be done during recording)

3To stop recording, press STOP on the CD Recorder/Player.

‹ CD-SYNC and RECORD go out.

•To interrupt recording, press PAUSE.

‹RECORD starts to flash. To resume, press PLAY on the CD Recorder/Player.

After recording the display will show UPDATE for several seconds.

Note:

-The CD Recorder/Player will not start until it recognizes a digital signal. Although the reaction time is less than 200 milliseconds, the very beginning of the music may sometimes not be recorded. If this happens, you can start the recording manually (see digital recording - unsynchronized).

-Recordings from DAT or DCC will only stop after 20 seconds silence.

Analogue recording from an external source

OPEN

RECORD

CLOSE

CD

SYNC

TRACK

D

OVER

UBB 1

SCAN

TRACK

TOTAL

REM

TIME

TOTAL

PAUSE

DIG

REM

TIME

OPEN

CD

REWRITABLE

REPEAT 1

C

LOSE

PAUSE

REPEAT 1

C O M

P A C

D

T

DISPLAY

I S C

R E

C

O R

D E R

SOURCE

C D R

7 6

5

REC

LEVEL

DUAL

DISPLAY

PHONES

Only make analog recordings if digital recording is not possible.

Preparing for analogue recording

1Make sure the disc is absolutely free of scratches and dust particles.

2Press SOURCE repeatedly until:

‹ANALOG appears on the display.

	FINALIZE	CD SYNC		SRC
DUBB 1		SHUFFLE SCAN		SHUFFLE
	AUTO TRACK		TOTAL REM TRACK TIME	TOTAL REM TRACK TIME
PAUSE DIG			ANALOG OPT PROG REPEAT 1	PAUSE PROG REPEAT 1

•If necessary, press DUAL to switch off the DUAL mode; DUAL will no longer appear on the display.

				TRACK OVER			TRACK
	RECORD		ERASE			DUAL
		CD SYNC			SRC
	FINALIZE
DUBB 1		SHUFFLE SCAN			SHUFFLE
	AUTO TRACK		TOTAL REM	TRACK TIME	TOTAL REM TRACK TIME

3Press AUTO/MANUAL to switch between auto and manual track numbering.

‹If Auto is selected (preferred), AUTO TRACK appears on the display.

•AUTO: The track number is automatically incremented after a silence on the original of at least 3 seconds.

•MANUAL: Track numbers can be incremented manually by pressing §. (minimum track length is 4 seconds.) (This can also be done in AUTO mode)

•Track numbers cannot be changed after recording.

4With the recorder stopped, press RECORD to enter Record standby mode.

‹ RECORD will flash

RECORD		ERASE	TRACK OVER		DUAL	TRACK
	CD SYNC			SRC
FINALIZE
DUBB 1	SHUFFLE SCAN			SHUFFLE
AUTO TRACK		TOTAL REM	TRACK TIME	TOTAL REM TRACK TIME

5Play the source first to set the optimal recording level on the CD Recorder/Player.

6Press REC LEVEL (+ or -) repeatedly until all the blue segments on the Record/Play level bar light up continuously but the red segments do not during the loudest passages. ‹ The display will show -3DB or 0DB or 3DB or 6DB

7Stop the source.

Start analogue recording

1To start recording, press PLAY on the CD Recorder/Player and immediately start the source.

‹RECORD lights continuously.The track number and recording time used appear on the display.

•To record a 3-second silence at the start of a track, press PAUSE.

•To check the (remaining) recording time, press DISPLAY. (This can also be done during the recording)

2To stop recording, press STOP on the CD Recorder/Player. ‹ RECORD will go out.

•To interrupt recording, press PAUSE.

‹ RECORD will start to flash. Resume at step 1.

After recording the display will show UPDATE for several seconds.

Note: With AUTO TRACK on, the recorder will stop automatically after a 20 seconds silence.

With AUTO TRACK off, the AUTO STOP mode is disabled.

16