Philips DVDR80/99 owner manual DV S-VIDEO Video Audio Left Right

Hookups (cont’d) 17

Connecting to Other Equipment

Dubbing Videotape to a DVD+R/DVD+RW

OPEN/CLOSE

STANDBY-ON

You can connect a Video Cassette Recorder (VCR), Camcorder, or DVD Player to the Recorder’s CAM or IN-EXT jacks.

A sample connection with a Camcorder is shown here, using the CAM 1 AUDIO/VIDEO IN jacks on the front of the Recorder. These jacks are the most easily accessible. Other equipment will con- nect similarly, but this is a common connection possibility.

You will need this connection to copy videotapes onto a DVD+R or DVD+RW. There are more Component Video, S-Video, Digital Video, and Audio In jacks on the front and rear of the Recorder. If your other equipment has these jacks, use them instead. Use the IN-EXT jacks on the rear of the Recorder for permanent connections.That will hide the cables from view.

1 Connect the DVD Recorder directly to your TV. Choose a connection from pages 10-16.

2 To access the jacks on the front of the Recorder, flip down the door that covers the jacks. Press where the door is marked OPEN :.

3 Connect a video cable to the VIDEO OUT jack of your Camcorder and to the yellow CAM 1 VIDEO IN jack on the front of the DVD Recorder. Use an RCA-style video cable, which is usually marked with yellow. (One video cable is supplied with the Recorder.)

4 Connect audio cables to the AUDIO OUT jacks of your Camcorder and to the red and white CAM 1 AUDIO IN jacks on the front of the DVD Recorder. Most audio cables are marked with red and white. Match the cable colors to the jack colors. (One pair of audio cables is supplied with the DVD Recorder.)

5 When all connections are complete, connect all the equipment to power. Turn on all the equipment. Press STANDBY-ON y on the front of the DVD Recorder to turn it on.

6 Set your TV to the correct Video In channel. This will be channel 3 or 4 or a specific Video In channel, depending on your connection between the Recorder and the TV. Refer to the connection details on pages 9-16. Or, simply go to channel 5 on your TV, then change channels down until you see the DVD Recorder’s logo. Initial Setup will appear the first time you turn on the Recorder. See pages 18-20 to do Initial Setup first.

7 To watch or record the material playing on the other equipment, press MONITOR to put the Recorder in Monitor mode. Press CH+8 or CH-9 to select CAM1 at the Recorder. This is located after your highest TV channel and before your lowest TV channel. Choose CAM1 if you used the connection shown on this page (with the jacks on the front of the Recorder). If you use the IN EXT 1 or IN EXT 2 jacks on the rear of the Recorder instead, choose channel EXT 1 or EXT 2. Choose the chan- nel that matches the jacks to which you connected the other equipment.

Start playing the material by pressing PLAY on the other equip- ment. Press Record I on the front of the DVD Recorder to start recording. See page 21.

DVDR 80

UP

GUIDE

T	R
	I
F	G
L	H
E	T
	DOWN

OPEN

S-VIDEO	VIDEO		L AUDIO R	DV IN
		CAM 1		CAM 2

DV S-VIDEO VIDEO AUDIO

LEFT RIGHT

Helpful Hints

•Use the DV IN CAM 2 jack to connect the Recorder to a Personal Computer that has a Digital Video output.The PC must have an IEEE 1394 Firewire connector. Limited PC applications may be supported. You also can use this jack to connect the Recorder to Digital Video or Hi-8 camcorders. If you use the DV IN CAM 2 jack, choose CAM 2 at the Recorder in Monitor mode to see the material playing on other equip- ment.

•Most prerecorded videotapes and DVDs are copy protected. If you try to copy them, the Recorder display may show “COPY PROTECT.”

•If the Recorder’s display shows “NO SIGNAL,” adjust the track- ing or play the tape at the VCR/Camcorder.

•Do not connect a Progressive Scan video source (such as a DVD Player) to the IN EXT 1 COMPONENT VIDEO jacks.The Recorder cannot receive Progressive Scan video.