Philips VRX463 warranty Press the Menu button. Wait for a few seconds

44 Setting the Controller to Operate a Cable Box (cont’d)

7

Use the Number buttons to enter the two-digit code for your Cable Box. (See list below.)

SELECT CODE NUMBER OF YOUR CABLE BOX 02

TO TEST PUSH MENU

DID CABLE BOX CHANGE TO CHANNEL 09?

1 YES 2 NO

TO END PUSH EXIT

CABLE BOX/DSS RECEIVER CODES

.GENERAL INSTRUMENTS .	.01, 02, 03, 04, 05, 06, 07
HAMLIN	. . . . . . . . . . . . . . .21, 22
JERROLD	.01, 02, 03, 04, 05, 06, 07
OAK	. . . . . . . . . . . .16, 17, 18
PANASONIC	. . . . . . . . . . . . . . .19, 20
PIONEER	. . . . . . . . . . . . . . .11, 12
SCIENTIFIC ATLANTA	. . . . . . . . . . . .08, 09, 10
TOCOM	. . . . . . . . . . . .23, 24, 25
ZENITH	. . . . . . . . . . . .13, 14, 15
MAGNAVOX DSS Receiver .	. . . . . . . . . . . . . . .42, 43
RCA DSS Receiver	. . . . . . . . . . . . . . . . . .40
SONY DSS Receiver	. . . . . . . . . . . . . . . . . .41

11

CBL/DSS	VCR	TV
PAUSE/STILL	POWER	MUTE

PLAY

REWFF

EJECTF.ADV

STOP

VCR PLUS+/ENTER

EXIT/STATUSCLEAR

MENU 8

VOL	JOG/SHUTTLE
	CHANNEL

8	9		1	2			3
			4	5			6
Press the MENU button. Wait for a few seconds.
• If the Cable Box changes to channel 09, go to step 9.			7	8			9
• If the Cable Box doesn’t change to channel 09, press the		100				0	GO-TO
Number 2 button to select NO. Use the Number buttons to
		REC /OTR			INDEX		MEMO
enter a different code for your Cable Box. Press the MENU but-					VAR.
					SLOW

ton. When the Cable Box changes to channel 09, go to step 9. SPEED VCR/TV SLOW TRACKING SKIP

9	SEARCH
	REMOTE LOCATOR

Press the Number 1 button to select YES.

7

10

10

A zero will appear in the SELECT OUTPUT CH menu. Press one Number button (3 or 4) to complete the out- put channel of your Cable Box (channel 03 or 04).

•Press 0 if you connected the VIDEO/AUDIO OUT Jacks of the Cable Box to the VCR’s VIDEO/AUDIO IN Jacks. A/V CON- NECT A/V REAR ONLY will appear.

•If you make a mistake, press the CLEAR button, then enter the correct output channel.

SELECT OUTPUT CH

OF YOUR CABLE BOX

03

TO CONTINUE PUSH MENU

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

11

Press the MENU button or the EXIT/STATUS button.

“CABLE BOX CONTROL IS ON” will appear for five seconds.

Helpful Hints

•If your Cable Box does not respond to any of the codes at step 8, the Controller will not change channels at the Cable Box during a timer recording. You must select the chan- nel to be recorded at the Cable Box before a timer recording begins. Enter the Cable Box output channel (03 or 04) at step 5 on page 35. Leave the Cable Box on for the timer recording. See page eight for details. You may want to exchange your current Cable Box for one that can be controlled by the VCR’s Controller.

•The Controller can change channels at the Cable Box only during a timer recording.