Manuals / Philips / TV and Video / VCR

Philips VRX463 warranty Repeat Playback, Press the VCR button, then press the Menu button

Models: VRX463

1 64

Download 64 pages 23.21 Kb

Page 54

54 Repeat Playback

Follow the steps below to program the VCR to play a tape over and over.

1

Press the VCR button, then press the MENU button.

TO SELECT PUSH NO. SHOWN

1PROGRAM

2VCR SET UP

3TUNER SET UP

4INPUT SELECT

5SET CLOCK

6SET REMOTE LOCATOR

TO END PUSH EXIT

2

Press the Number 2 button to select VCR SET UP.

TO SELECT PUSH NO. SHOWN

1 SET REPEAT PLAY (OFF)

2ON SCREEN MODE

3LANGUAGE

4SET VCR PLUS+ CH

5SET CABLE BOX

6SET DSS RECEIVER

7AUDIO OUT

8 VIDEO STABILIZER (OFF) TO END PUSH EXIT

3

Press the Number 1 button so that (ON) appears to the right of SET REPEAT PLAY.

Each time you press the Number 1 button, you turn SET REPEAT PLAY ON or OFF.

4

Press the EXIT/STATUS button. Now, when a tape has fin- ished playing, the VCR will rewind it and start playback again. This will happen until the tape has played 20 times. The PLAY light on the display panel will flash during tape playback and while rewind- ing. TV programming will appear while the tape is rewinding.

	CBL/DSS	VCR	TV	1
	PAUSE/STILL	POWER	MUTE
	REW	PLAY	FF
	REW		FF
4	EJECT	STOP	F.ADV
		STOP
	VCR PLUS+/ENTER
	EXIT/STATUS		CLEAR
		MENU
	JOG/SHUTTLE
	VOL		CHANNEL
			CHANNEL

3	4	5	6	2
	1	2	3
	7	8	9
	100	0	GO-TO

REC /OTR	INDEX	MEMO
	VAR.
	SLOW
SPEED	VCR/TV SLOW	TRACKING SKIP

SEARCH

REMOTE LOCATOR

Helpful Hints

•The VCR will stay in Repeat Play mode until you cancel Repeat Play mode. To do this, follow steps 1 - 2 above. At step 3, press the Number 1 button so that (OFF) appears to the right of SET REPEAT PLAY. Press the EXIT/STATUS button to exit.

Image 54

Philips VRX463 warranty Repeat Playback, Press the VCR button, then press the Menu button

Contents

Video Cassette Recorder VRX463 Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR MaintenanceHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Antenna Or CableRecording or Viewing a Scrambled or Unscrambled Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR Turned OffPlaying a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Antenna in Jack On back of TVVCR will come on Press the VCR button, then press the Power buttonTurning on Your VCR Turn on the TVPress the Menu button. The menu shown below will appear Wait for the VCR to program channelsPress the VCR button, then press the Menu button to Press the Number 3 button to select Tuner SET UPProgramming Channels Bring up the main menu displayPress the Menu button to bring up the main menu display Adding/Deleting ChannelsPress the VCR button Press the Number 4 button to select ADD/DELETE CHPress the Number 3 button to select SET Manual Clock Setting the ClockPress the VCR button, then press the Menu button Press the EXIT/STATUS buttonSetting the Clock cont’d Time Zone SelectionPress the Number 4 button to select SET Time Zone Manual PBS Channel Selection Setting the Clock cont’d Automatic PBS Channel SelectionDaylight-Saving Time Selection Press the EXIT/STATUS button to exitLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons Eject Button REWind ButtonStop Button JOG/SHUTTLE ButtonDisplay Panel Remote Sensor Display Panel cont’dOTR Light Tape Speed Lights Memory LightFront Panel Rear Panel Setting the Remote Control to Operate a TV 2Find the code for your TV 4Repeat stepCable BOX/DSS Receiver Codes Find the code for your Cable Box/DSS Receiver Repeat stepCounter will remain on the screen Press the Number 2 button to select on Screen ModeOn-Screen Status Displays Sound ProgramWhen you find the remote control, point the remote at Remote LocatorPlaying Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape Recording Appear on the display panelOne Touch Recording Starting an OTRStopping an OTR Recording One Channel/Watching Another Select a once, daily, or weekly recording Timer RecordingPress the Number 1 button to select Program RecordingInstructions continue on Box/DSS Receiver onFollow to set the recording’s stop time Timer Recording cont’d Tape SpeedsChecking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Connecting the Controller Cable Box or DSS Receiver ControllerSetting the Controller to Operate a Cable Box Press the Number 5 button to select SET Cable BOXNumber 2 button to select NO. Use the Number buttons to Ton. When the Cable Box changes to channel 09, go to stepPress the Menu button. Wait for a few seconds Press the Menu button or the EXIT/STATUS buttonPress the Number 6 button to select SET DSS Receiver Press the Number 1 button to set the DSS ReceiverController to on Press the Menu button Press the Number 1 button to select YESVideo cable Rerecording Tape DuplicationAudio cables VCR 1 will play your tape. Insert a prerecorded tape in VCRIndex Search Insert a tapeMulti-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Press the Number 1 button so that on appears besideHi-Fi Stereo Tape Playback Using the Tape Counter Tape Counter MemoryStop the tape To bring up the Goto displayBegin tape playback Turn off VCRRepeat Playback Video Stabilizer Video StabilizerViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DSS Receiver Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories