10Adjustments and Settings
Power Control
Power Control provides convenient functions for power saving.
Energy Save
You can save power consumption by decreasing the picture brightness. When you need not watch the screen and want to enjoy only audio, you can also deactivate the screen.
1Press HOME MENU.
2 | Select “Power Control”. ( | / | then ENTER) | ||
3 | Select “Energy Save”. ( | / | then ENTER) | ||
4 | Select “Save” or | “Picture Off”. ( / then ENTER) | |||
|
|
|
| ||
|
| Item | Description | ||
|
| Standard | Does not decrease picture brightness. | ||
|
| (factory default) |
|
|
|
|
|
|
| ||
|
| Save | Decreases picture brightness to save power. | ||
|
|
|
| ||
|
| Picture Off | Deactivates the screen to save power. To | ||
|
|
| restore the screen display, press any button | ||
|
|
| other than VOL +/– and MUTING. | ||
|
|
| This setting is not memorized by the system. | ||
|
|
|
|
|
|
5Press HOME MENU to exit the menu.
•You can also select this function using the Home menu when the input source is a PC.
No Signal off (AV mode only)
The system will be automatically placed into the standby mode if no signal is received for 15 minutes.
1Press HOME MENU.
2 | Select “Power Control”. ( | / | then ENTER) |
3 | Select “No Signal off”. ( | / | then ENTER) |
4 | Select “Enable”. ( / then ENTER) | ||
Item | Description |
Disable | Does not place the system into the |
(factory default) standby mode. | |
|
|
Enable | Places the system into the standby mode if |
| no signal is received for 15 minutes. |
|
|
5Press HOME MENU to exit the menu.
•Five minutes before the system is placed into the standby mode, a message appears every minute.
•The system may not be placed into the standby mode when noise signals are present at the Media Receiver after a TV program finishes.
44
No Operation off (AV mode only)
The system will be automatically placed into the standby mode when no operation is performed for three hours.
1Press HOME MENU.
2 | Select “Power Control”. ( / | then ENTER) |
3 | Select “No Operation off”. ( / | then ENTER) |
4 | Select “Enable”. ( / then ENTER) | |
Item | Description |
Disable | Does not place the system into the |
(factory default) standby mode. | |
|
|
Enable | Places the system into the standby mode if |
| no operation is performed for three hours. |
|
|
5Press HOME MENU to exit the menu.
•Five minutes before the system is placed into the standby mode, a message appears every minute.
Power Management (PC mode only)
The system will be automatically placed into the standby mode when no signal is received from the personal computer.
1Press HOME MENU.
2 | Select “Power Control”. ( / then ENTER) | ||
3 | Select “Power Management”. ( | / | then ENTER) |
4 | Select “Mode1” or “Mode2”. ( | / | then ENTER) |
Item | Description |
Off | No power management |
(factory default) |
|
|
|
Mode1 | • Places the system into the standby mode |
| when no signal is received from the |
| personal computer for eight minutes. |
| • Even when you start using the computer |
| and a signal is received again, the system |
| stays off. |
| • The system is switched on again by |
| pressing STANDBY/ON on the Plasma |
| Display or TV on the remote control |
| unit. |
|
|
Mode2 | • Places the system into the standby mode |
| when no signal is received for eight |
| seconds. |
| • When you start using the computer and a |
| signal is received again, the system is |
| switched on. |
| • The system is switched on again by |
| pressing STANDBY/ON on the Plasma |
| Display or TV on the remote control |
| unit. |
|
|
5Press HOME MENU to exit the menu.
En
