Pioneer VSX-1021-K manual 22

03Connecting your equipment

Connecting to a wireless LAN

Wireless connection to the network is possible through a wireless LAN connection. Use the separately sold AS-WL300 for connection.

OUT		LAN(10/100)		COAXIAL ASSIGNAB
	DC OUTPUT			IN 1 IN 2
	forWIRELESS LAN
	(OUTPUT 5V	0.6 A MAX)		(DVD) (CD)
(OUTPUT 5 V					Internet
ADAPTER PORT
0.1 A MAX)
TENNA
UNBAL					Modem
AM LOOP
IUS	A R FRONT L		CENTER	RSURROUN
IN
SUBWOOFER
	CAUTION:	ATTENTION:			Router
PRE OUT	SPEAKER IMPEDANCE ENCEINTE D’IMPEDANCE DE			SPE
	6 -16 .	6 -16 .

WAN

DC 5V Ethernet WPS

Wireless LAN convereter (AS-WL300)

!If using two remote controls (at the same time), the IR receiver’s remote sensor takes priority over the remote sensor on the front panel.

1Connect the IR receiver sensor to the IR IN jack on the rear of this receiver.

Closet or shelving unit
Pioneer								Non-Pioneer
component								component
		CONTROL							IR
		IN	OUT						IN
HDMI	IN 1 VIDEO 1 IN			BD IN DVD IN		DVR/BDR IN		OUT	LAN
ASSIGNABLE 1								DC OUTPUT
								forWIRELESS LAN
								(OUTPUT 5V	0.6 A MAX)
CONTROL	VIDEO				AUDIO
IN		ZONE 2			DVR/BDR CD-R/TAPE	ZONE 2
								ADAPTER PORT
	OUT		TV/SAT	VIDEO 1		L
OUT							(OUTPUT 5 V
	MONITOR		IN	IN	OUT	OUT	0.1 A MAX)
IR IN	OUT					R ANTENNA
OUT	DVR/					CD	FM UNBAL
	BDR					L	75	AM LOOP
		OUT	IN	DVD IN	IN	IN	SIRIUS	A R FRONT L C
	IN 1					R
	(DVD)
	ASSIGN							IN
	ABLE
	IN 2					L
	(DVR/
	BDR)				IN	IN
						R	SUBWOOFER
	MONITOR
	OUT	Y	PB	PR	TV/SAT VIDEO 1	DVD		CAUTION:	ATTENTION
	COMPONENT VIDEO							SPEAKER IMPEDANCE ENCEINTE D’IMPE
							PRE OUT 6 -16 .		6 -16 .

IR receiver

Operating other Pioneer components with this unit’s sensor

Many Pioneer components have SR CONTROL jacks which can be used to link components together so that you can use just the remote sensor of one component. When you use a remote control, the control signal is passed along the chain to the appropriate component.

!If you want to control all your components using this receiver’s remote control, see page 52.

!If you have connected a remote control to the CONTROL IN jack (using a mini-plug cable), you won’t be able to control this unit using the remote sensor.

Important

!Note that if you use this feature, make sure that you also have at least one set of analog audio, video or HDMI jacks connected to another component for grounding purposes.

1 Decide which component you want to

use the remote sensor of.

When you want to control any component in the

HDMI	IN 1	VIDEO 1 IN		BD IN		DVD IN	DVR/BD
ASSIGNABLE 1
CONTROL	VIDEO				AUDIO
IN	ZONE 2				DVR/BDR CD-R/TAPE		ZONE 2
	OUT		TV/SAT	VIDEO 1			L
OUT
	MONITOR		IN	IN	OUT		OUT
IR IN	OUT						R
OUT	DVR/						CD
	BDR						L
	OUT		IN	DVD IN	IN		IN
	IN 1						R
	(DVD)
	ASSIGN
	ABLE
	IN 2						L
	(DVR/
	BDR)				IN		IN
							R
	MONITOR
	OUT	Y	PB	PR	TV/SAT VIDEO 1		DVD
	COMPONENT VIDEO
					IN	OUT	IN	OUT
					CONTROL		CONTROL

3Continue the chain in the same way for as many components as you have.

Connecting an IR receiver

If you keep your stereo components in a closed cabinet or shelving unit, or you wish to use the sub zone remote control in another zone, you can use an optional IR receiver (such as a Niles or Xantech unit) to control your system instead of the remote sensor on the front panel of this receiver.

!Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window.

!Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR compatibility.

2Connect the IR IN jack of another component to the IR OUT jack on the rear of this receiver to link it to the IR receiver. Please see the manual supplied with your IR receiver for the type of cable necessary for the connection.

!If you want to link a Pioneer component to the IR receiver, see Operating other Pioneer components with this unit’s sensor on page 22 to connect to the CONTROL jacks instead of the IR OUT jack.

chain, this is the remote sensor at which you’ll

point the corresponding remote control.

2 Connect the CONTROL OUT jack of that

component to the CONTROL IN jack of

another Pioneer component.

Use a cable with a mono mini-plug on each end

for the connection.

22En