10Controlling the rest of your system

Controlling the rest of your system

Operating multiple receivers

If you can’t find a preset code that matches the component you want to control, you can still

About the Remote Setup menu

The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the respective items.

Setting What it does

Preset codes can be set for the various input functions. The remote control codes of a number of other devices

Preset (including products of other brands)

recall are preset in the remote control to allow these devices to be operated. See Selecting preset codes directly on page 52 .

If the desired operations cannot be performed even though you have set

Code the preset codes, the remote control learning signals of other devices can be learned

directly. See Programming signals from other remote controls on page 53 .

A series of the remote control operations for starting listening or viewing

Multi can be programmed. Multiple remote operation control codes can be set for the differ-

ent input functions. See Multi Operation and System Off on page 54 .

This is a function for automatically turning off the power of devices con-

System nected to the receiver. Multiple remote

off control codes can be set, as desired. See Multi Operation and System Off on page 54 .

Setting

What it does

 

This is a setting for changing only the

 

remote control unit’s operation screen,

 

without changing the receiver’s input,

Direct

when the remote control unit’s input

function buttons are pressed. This

function

is convenient for using the remote

 

 

control unit for devices not connected

 

to the receiver. See Direct function on

 

page 54 .

 

This function is used to erase remote

 

control codes that have been learned.

Erase

Codes learned for the different input

learning

functions can be erased individually.

 

See Erasing one of the remote control

 

button settings on page 53 .

 

This is a function for resetting preset

 

codes that have been set. Key reset-

Reset

ting can be done for individual input

function

functions. See Erasing all learnt set-

 

tings that are in one input function on

 

page 53 .

 

This is a function for resetting all

 

remote control unit settings you have

All reset

made to the defaults set upon ship-

 

ment from the factory. See Resetting

 

the remote control settings on page 55 .

 

If you have multiple Pioneer receivers,

 

amplifiers, etc., this setting can be

Change

used to prevent other units from oper-

RC mode

ating simultaneously when the remote

 

control unit is operated. See Operating

 

multiple receivers on page 52 .

Note

!You can cancel or exit any of the steps by pressing RCU SETUP.

!After one minute of inactivity, the remote automatically exits the operation.

Up to four receivers can be operated discretely using this receiver’s remote control when using multiple receivers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the preset code to set the remote control setting.

!Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page 68 ).

1Press and hold RCU SETUP, then press ‘4’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

!To cancel the preset setup mode press

RCU SETUP.

2Press the number button for the receiver (“Receiver 1” to “Receiver 4”) you wish to operate.

For example, to operate “Receiver 2”, press ‘2’. If the LED lights for one second and continues to flash, the setting has been successfully completed.

When the preset code is input, the LED flashes three times to indicate that the setting has failed.

Setting the remote to control other components

Most components can be assigned to one of the input function buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.

However, there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for the manufacturer in the remote control will not work for the model that you are using.

teach the remote individual commands from another remote control (see Programming signals from other remote controls on page 53 ).

!For greater convenience, assign the TV connected to the MONITOR OUT terminal to the TV CTRL button, and assign your satellite/ cable receiver or set-top box connected to the TV/SAT input terminal to the TV/SAT input button. If a single device is connected to both terminals, that device should be assigned to both the TV CTRL and TV/SAT input buttons.

!Devices may be assigned to the following input function buttons.

RECEIVER MULTI

 

SOURCE

 

OPERATION

 

 

RCU SETUP

 

 

 

BDR

 

BD

DVD

DVR

HDMI

SAT

 

 

 

TV

CD

HMG

ADPT

USB

 

 

TV CTRL

iPod

TUNER

SIRIUS

 

INPUT SELECT

ZONE2

RECEIVER

Selecting preset codes directly

1Press and hold RCU SETUP, then press ‘1’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

!To cancel the preset setup mode press

RCU SETUP.

2Press the input function button for the component you want to control.

When assigning preset codes to TV CONTROL, press TV CTRL here.

The LED blinks once and flashes continuously.

52En