05Listening to your system
Listening with Acoustic Calibration
EQ
You can listen to sources using the Acoustic Calibration Equalization set in Automatically setting up for surround sound on page 39 or Acoustic Calibration EQ on page 61. Refer to these pages for more on acoustic calibration equalization.
•While listening to a source, press ACOUSTIC CAL. to select an Acoustic Calibration EQ setting.
RECEIVER | 1/4 |
RECEIVER STREAM
DIRECT
SIGNAL ACOUSTIC
SELECTCAL.
LISTENING STEREO
MODE
STANDARD THX
ADVANCED ADVANCED
CINEMA CONCERT
ACOUSTIC |
|
|
|
|
|
|
| TUNER | SBCH | MULTI ROOM & SOURCE | |
CAL. | MIDNIGHT | TONE | OPTION |
|
| DIGITALNR | CLASS | STATION | MODE | CONTROL | ON/OFF |
PHONES | SPSYSTEM | SIGNAL | VIDEO | TAPE2 | STREAM | SETUP |
| VIDEOINPUT |
|
| |
|
|
|
|
| |||||||
| A/B | SELECT | SELECT | MONITOR | DIRECT | MIC | DIGITALIN |
|
|
|
|
|
|
|
|
|
|
|
| VIDEO | L AUDIO | R | |
Press repeatedly to select between:
•ALL CH ADJ – No special weighting is given to any one channel.
•FRONT CH ALIGN – All speakers are heard in accordance with the front speaker settings.
•CUSTOM 1/2 – Custom settings
•OFF – Switches Acoustic Calibration EQ off.
Selecting the input signal type
Most of the audio inputs have both analog and digital jacks. You can select the type of signal to be used in each case.
The input signal type for the current input is indicated in the display. With digital signals, the signal type (Dolby Digital or DTS) also shows in the display.
The default AUTO setting is usually sufficient, letting the receiver decide the most suitable signal type. However, if you want to record from the DVR/VCR1 IN/OUT jacks, then you should set the input signal type to analog.
If you have selected the USB interface or the multichannel analog inputs as your input source, see Selecting USB and multichannel analog input channels below.
48
•Press SIGNAL SELECT to select the type of input signal for the current source.
With the remote, you may need to press RECEIVER on the
Home menu (
) first before reaching the receiver menu
screen shown below (use the (cursor left/right) soft keys to go to the previous/next menu screen).
RECEIVER | 1/4 |
RECEIVER STREAM
DIRECT
SIGNAL ACOUSTIC
SELECTCAL.
LISTENING STEREO
MODE
STANDARD THX
ADVANCED ADVANCED
CINEMA CONCERT
ACOUSTIC |
|
|
|
|
|
|
| TUNER | SBCH | MULTI ROOM & SOURCE | |
CAL. | MIDNIGHT | TONE | OPTION |
|
| DIGITALNR | CLASS | STATION | MODE | CONTROL | ON/OFF |
PHONES | SPSYSTEM | SIGNAL | VIDEO | TAPE2 | STREAM | SETUP |
| VIDEOINPUT |
|
| |
|
|
|
|
| |||||||
| A/B | SELECT | SELECT | MONITOR | DIRECT | MIC | DIGITALIN |
|
|
|
|
|
|
|
|
|
|
|
| VIDEO | L AUDIO | R | |
Press repeatedly to choose between:
•ANALOG – Selects an analog signal.
•
– Selects an i.LINK signal.
•DIGITAL – Selects an optical or coaxial digital signal.
•2 RF – Selects a 2 RF signal.
•AUTO – This is the default setting. The receiver selects the first available signal in the following order: 
; 2 RF; DIGITAL; ANALOG.
Note
•If no digital inputs (including the 2 RF input) are assigned for the current source, the input signal type will default to ANALOG.
•When using DIGITAL IN terminals the following digital signal formats are supported: Dolby Digital, DTS and PCM (32, 44.1, 48, 88.2 and 96 kHz sampling frequencies). If you are using the i.LINK connectors,
ANALOG.
•Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.
•Even when i.LINK is selected and the i.LINK indicator lights, you won’t hear any sound if the output settings of your i.LINK device are off.
•The audio signal from karaoke microphones and some LDs is not output from the digital outputs. Select ANALOG to listen to these formats.
En
