08Controlling other equipment
Using System off
•From the remote control Home menu 
press
SYSTEM OFF.
The command sequence you programmed will run, then all Pioneer components will switch off, followed by this receiver.
2Connect the CONTROL OUT jack of that component to the CONTROL IN jack of another Pioneer component.
Use a cable with a mono
HOME 1/3
RECEIVER 
RECEIVER
INPUT 1 | 2 | 3 |
| CONTROL |
| CONTROL |
IN | OUT | IN | OUT |
DVD | TV | SAT |
|
|
|
|
|
|
| |
/ LD | / DVD |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
DVR | CD | TUNER |
|
|
|
|
|
|
| |
/ VCR1 |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||||
TV | MULTI | SYSTEM |
|
|
|
|
| |||
CONT | OPERATION | OFF |
|
| CONTROL |
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| MONITOR |
|
|
| |
| SETUP |
|
| OUT | IN | OUT 1 |
|
| ANTENNA | |
|
|
|
|
|
| |||||
|
|
| S400 | (AUDIO) | MULTI- | MONITOR |
| REMOTE IN |
| |
|
|
|
|
|
| MULTI ROOM & |
| |||
|
|
|
|
| ROOM & | OUT 2 |
| SOURCE |
| |
|
|
|
|
| SOURCE |
| COMPONENT VIDEO |
| ||
|
|
|
|
| DVD/ | IN | (DVD/ | Y | AM LOOP | |
|
|
|
|
| LD | LD) | ANTENNA | |||
|
|
|
|
| IN |
| IN |
|
| |
|
|
| AUDIO | POWER | TV/ |
| 1 Y | MONITOR |
| |
|
|
|
| AMP | IN |
| OUT | FM | ||
|
|
|
| IN | DVD |
| PB | |||
Switching components on and off |
|
|
| 75Ω UNBAL | ||||||
R | L | IN |
| PR | PR |
| ||||
IN |
|
| ||||||||
|
|
|
|
|
|
| PB |
|
| |
|
|
|
|
| SAT | IN |
|
|
| |
using the 12 volt trigger | 3 Continue the chain in the same way for as many | |||||||||
You can connect components in your system (such as a | ||||||||||
components as you have. |
|
|
| |||||||
screen or projector) to this receiver so that they switch on |
|
|
| |||||||
|
|
|
|
|
|
| ||||
or off using a 12 volt trigger when you select an input | Note |
|
|
|
|
| ||||
function. However, you must specify which input |
|
|
|
|
| |||||
functions switch on which trigger(s) using the Expert | • If you want to control all your components using this | |||||||||
Setup menu (see 12 Volt Trigger on page 95 to do this). | ||||||||||
receiver’s remote control, refer to Using the remote | ||||||||||
Note that this will only work with components that have a | ||||||||||
control with other components on page 67 and | ||||||||||
standby mode. |
|
| ||||||||
|
| Programming signals from other remote controls on | ||||||||
|
|
| ||||||||
• Connect the 12V TRIGGER jack of this receiver to | page 69. |
|
|
|
|
| ||||
the 12V TRIGGER of another component. |
|
|
|
|
|
|
| |||
Two connections are possible. Use a cable with a mono |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||||
After you’ve specified the input functions that will switch on the trigger(s), you’ll be able to switch the component on or off just by pressing the input function(s) you’ve set on page 95.
Operating other Pioneer components with this unit’s sensor
Many Pioneer components have SR CONTROL jacks which can be used to link components together so that you can use just the remote sensor of one component. When you use a remote control, the control signal is passed along the chain to the appropriate component.
Note that if you use this feature, make sure that you also have at least one set of analog audio jacks connected to another component for grounding purposes.
1Decide which component you want to use the remote sensor of.
When you want to control any component in the chain, this is the remote sensor at which you’ll point the corresponding remote control.
74
En
