Using other functions
Resetting the system
Use this feature to reset the system to its factory default settings (see Default receiver settings below).
1Switch the receiver into standby.
2While holding down the front panel DIGITAL NR
button, press and hold STANDBY/ON for about three seconds.
The display shows RESET?.
3Press the front panel OPTION + button. The display shows OK?.
4Within 5 seconds, press OPTION
The receiver should now be reset.
Note
•This doesn’t affect the presets that you have programmed into the remote control (see Using the remote control with other components on page 67). See Resetting the remote control below to do this.
Default receiver settings
The table below shows the factory default settings. When you reset the system, the receiver reverts to these defaults:
Setting type | Default setting | Page ref. |
Input | DVD/LD |
|
|
|
|
Master volume | – – – dB (no sound) |
|
|
|
|
Listening mode | STANDARD (video inputs, | page 43 |
| multichannel inputs, USB) |
|
| STEREO (audio inputs) |
|
|
|
|
Advanced surround | 90 (5/7CH STEREO) | page 45 |
effect level | 50 (all other modes) |
|
|
|
|
Listening mode (w/ | STEREO | page 46 |
headphones) |
|
|
|
|
|
USB / multichannel | 8 channels | page 47 |
input channel setting |
|
|
|
|
|
Stream Direct mode | SD:1 NORMAL (ON) | page 47 |
|
|
|
Acoustic Calibration | OFF (switches to ALL CH ADJ | page 48 |
EQ | after the Auto Surround Setup) |
|
|
|
|
Input signal select | AUTO except multichannel | page 48 |
| inputs (ANALOG) and USB |
|
| (DIGITAL) |
|
|
|
|
Surround Back | ON (with surround back | page 50 |
Channel mode | speaker(s) connected) |
|
|
|
|
Virtual Surround Back | OFF | page 51 |
mode |
|
|
|
|
|
OFF | page 52 | |
|
|
|
Midnight/Loudness | OFF | page 52 |
|
|
|
09
Setting type | Default setting | Page ref. |
Tone | BYPASS | page 52 |
|
|
|
Digital NR | OFF | page 53 |
|
|
|
Dual mono | CH1 | page 53 |
|
|
|
Speakers Systems | Normal Surround | page 58 |
|
|
|
Speaker B setting | Second Zone | page 58 |
|
|
|
Speakers (front, | All SMALL | page 59 |
center, surround, |
|
|
surround back) setting |
|
|
|
|
|
Subwoofer setting | YES | page 59 |
|
|
|
Crossover frequency | 80Hz | page 59 |
|
|
|
Channel levels | All 0 dB (no adjustment) | page 60 |
|
|
|
Speaker distance | All 10 ft. | page 61 |
settings |
|
|
|
|
|
Acoustic Calibration | 0dB (no calibration) | page 61 |
|
|
|
OFF (switches to ON after the | page 61 | |
| Auto Surround Setup) |
|
|
|
|
Tape 2 monitor | OFF | page 75 |
|
|
|
Input attenuator | OFF (all inputs) | page 76 |
|
|
|
Sound delay | 0.0 frames | page 76 |
|
|
|
SACD gain | 0dB | page 77 |
|
|
|
Speaker A/B setting | A | page 80 |
|
|
|
Digital jack | page 90 | |
assignment |
| |
|
| |
|
| |
|
| |
|
| |
|
| |
| 2 RF (coaxial) – DVD/LD |
|
|
|
|
Component video jack | Component1 – DVD/LD | page 91 |
assignment | Component2 – OFF |
|
| Component3 – OFF |
|
|
|
|
Video input | MULTI IN – OFF | page 92 |
assignment | USB – OFF |
|
|
|
|
Bass Peak Level | OFF (No limit) | page 93 |
|
|
|
Dynamic range | OFF | page 94 |
control |
|
|
|
|
|
OSD overlay | ON | page 94 |
|
|
|
12 volt trigger | OFF · OFF | page 95 |
|
|
|
THX Ultra2 subwoofer | NO | page 96 |
|
|
|
Surround back | page 96 | |
speaker position |
|
|
|
|
|
79
En