Manuals / Powerware / Computer Equipment / Power Supply

Powerware 6000 VA, 5000 manual EBM Installation, C A U T I O N

Models: 6000 VA 5000

1 66

Download 66 pages 55.12 Kb

Page 25

EBM Installation

INSTALLATION

6.Align each joining bracket with the adjacent cabinet screw holes and secure with the supplied screws (see Figure 8).

7.If installing additional cabinets, repeat Step 6 for each cabinet.

UPS

Joining Bracket

EBM

Joining Bracket

Figure 8. Installing the Joining Brackets (Top View)

8.Continue to the following section, “EBM Installation.”

EBM Installation

C A U T I O N

A small amount of arcing may occur when connecting an EBM to the UPS. This is normal and will not harm personnel. Insert the EBM cable into the UPS battery connector quickly and firmly.

To install the optional EBM(s):

1.Verify that all battery circuit breakers are in the OFF (O) position (see Figure 9).

2.Plug the EBM cable of the first EBM into the UPS battery connector.

If additional EBMs are to be installed, plug the EBM cable of the second cabinet into the battery connector on the first EBM. Repeat for each additional EBM. Up to four EBMs may be connected to the UPS.

EATON Powerware® 9125 Two-in-One UPS (5000/6000 VA) User’s Guide S 164201513 Rev B	19
www.powerware.com

Image 25

Powerware 6000 VA, 5000 manual EBM Installation, C A U T I O N

Contents

Powerware 9125 Two-in-One UPS 5000/6000 VA User’s Guide FCC Part Class A EMC StatementsICES-003 Requesting a Declaration of Conformity Special Symbols Safety Warnings Table of ContentsInstallation ConfigurationTroubleshooting SpecificationsWarranty Testing New BatteriesIntroduction ChapterFigure 1. The Powerware 9125 UPS with Optional EBM S 5U rack height with the highest power density for a 6000 VA UPS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Chapter 2 Safety WarningsD A N G E R W A R N I N GSikkerhedsanvisninger C A U T I O NF A R E A D V A R S E LG E V A A R Belangrijke VeiligheidsinstructiesW A A R S C H U W I N G BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIESTarkeita Turvaohjeita O P G E L E TV A A R A V A R O I T U SA V E R T I S S E M E N T Consignes de sécuritéA T T E N T I O N CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONSW A R N U N G SicherheitswarnungenA C H T U N G V O R S I C H TP E R I C O L O Avvisi di sicurezzaA V V E R T E N Z A A T T E N Z I O N EF A R L I G Viktig SikkerhetsinformasionF O R S I K T I G F A R L I GC U I D A D O Regulamentos de SegurançaA D V E R T Ê N C I A P E R I G OОПАСНО Предупреждения по мерам безопасностиПРЕДУПРЕЖДЕНИЕ ОСТОРОЖНОP E L I G R O Advertencias de SeguridadA D V E R T E N C I A P R E C A U C I Ó NF A R A SäkerhetsföreskrifterV A R N I N G V I K T I G TUPS Setup InstallationInspecting the Equipment ChapterC A U T I O N Installing the UPS Internal BatteriesTower Setup Figure 6. UPS Cabinet with Pedestals 5. Carefully position the cabinets upright see FigureFigure 7. Tower UPS with an EBM C A U T I O N EBM InstallationConnectors Figure 9. Typical EBM InstallationPlug-Receptacle UPS Installation Remote Emergency Power-off Installation W A R N I N G To install the REPO switchC A U T I O N W A R N I N G Hardwired UPS InstallationC A U T I O N Figure 12. Hardwired UPS Rear Panel Figure 13. UPS Terminal Block Table 1. UPS Wiring SpecificationsTightening Page INSTALLATION Operation Starting the UPS on BatteryTurning the UPS On ChapterTurning the UPS Off Initiating the Battery TestOperating Modes Transferring the UPS to Bypass ModePress the On button for approximately eight seconds to transfer the UPS to Bypass mode. TheFigure 15. Load Level Indicators Normal ModeFigure 16. Battery Capacity Indicators Battery ModeStandby Mode Bypass ModeTo reconfigure the UPS default settings ConfigurationChapter C A U T I O NTable 2. Configuration Mode LEDs and Options Figure 17. Using Configuration ModeBar Graph Indicators OptionUSB Port Chapter 6 CommunicationTable 3. Communication Port Pin Assignment DB-9 Communication PortX-Slot Cards COMMUNICATION UPS and Battery Care Chapter 7 UPS MaintenanceWhen to Replace Batteries Storing the UPS and BatteriesReplacing Batteries How to Replace Extended Battery ModulesW A R N I N G 6. Reinstall the joining brackets if removed in Step C A U T I O N How to Replace Internal BatteriesTesting New Batteries W A R N I N G Recycling the Used Battery or UPSC A U T I O N C A U T I O NChapter SpecificationsTable 4. Model List Table 5. Electrical InputSPECIFICATIONS Table 7. Environmental and SafetyTable 6. Electrical Output 0C to 40C 32F to 104FTable 9. Battery Table 8. Weights and DimensionsTable 10. Battery Runtimes in Minutes Extended Battery Module EBMSPECIFICATIONS Audible Alarms and UPS Conditions Chapter 9 TroubleshootingSilencing an Audible Alarm Alarm or Condition Table 11. Troubleshooting GuidePossible Cause ActionPossible Cause Alarm or ConditionAction 2 minutes 112-150% for up toAll other countries Call your local service representative Service and SupportUnited States 1-800-356-5737 or Canada1-800-461-9166 ext Two-Year Limited Warranty US and Canada Chapter 10 WarrantyWARRANTY Product repaired or replaced pursuant to terms of Limited Warranty Ten-Year Pro-Rated Limited Warranty US and Canada10 Years of Warranted Life WARRANTY Load Protection Guarantee US and Canada