Manuals / Powerware / Computer Equipment / Power Supply

Powerware 6000 VA Transferring the UPS to Bypass Mode, Operating Modes, UPS to Bypass mode. The

Models: 6000 VA 5000

1 66

Download 66 pages 55.12 Kb

Page 37

Image 37

OPERATION

Transferring the UPS to Bypass Mode

NOTE When the UPS is in Bypass mode, Battery mode is not available and the UPS does not protect against power outages; however, the utility power continues to be passively filtered by the UPS.

Press the On button for approximately eight seconds to transfer the

UPS to Bypass mode. The

indicator illuminates.

Press the On Normal mode.

button again for approximately three seconds to return to

Operating Modes

Powerware 9125’s front panel indicates the UPS status through the UPS indicators. Figure 14 shows the UPS front panel indicators and controls.

Normal Mode Indicator

Battery Mode Indicator Bypass Mode Indicator

Test/Alarm Reset Button

Alarm Indicators (see page 51)

Bar Graph Indicators

Indicator Legend

Unlit

Lit

Flashing

Off Button

On Button

Figure 14. UPS Front Panel

EATON Powerware® 9125 Two-in-One UPS (5000/6000 VA) User’s Guide S 164201513 Rev B	31
www.powerware.com

Page 37

Image 37

Powerware 6000 VA Transferring the UPS to Bypass Mode, Operating Modes, UPS to Bypass mode. The, Press the On Normal mode

Contents

Powerware 9125 Two-in-One UPS 5000/6000 VA User’s Guide FCC Part Class A EMC StatementsICES-003 Requesting a Declaration of Conformity Special Symbols Safety Warnings Table of ContentsInstallation ConfigurationTroubleshooting SpecificationsWarranty Testing New BatteriesIntroduction ChapterFigure 1. The Powerware 9125 UPS with Optional EBM S 5U rack height with the highest power density for a 6000 VA UPS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Chapter 2 Safety WarningsD A N G E R W A R N I N GSikkerhedsanvisninger C A U T I O NF A R E A D V A R S E LG E V A A R Belangrijke VeiligheidsinstructiesW A A R S C H U W I N G BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIESTarkeita Turvaohjeita O P G E L E TV A A R A V A R O I T U SA V E R T I S S E M E N T Consignes de sécuritéA T T E N T I O N CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONSW A R N U N G SicherheitswarnungenA C H T U N G V O R S I C H TP E R I C O L O Avvisi di sicurezzaA V V E R T E N Z A A T T E N Z I O N EF A R L I G Viktig SikkerhetsinformasionF O R S I K T I G F A R L I GC U I D A D O Regulamentos de SegurançaA D V E R T Ê N C I A P E R I G OОПАСНО Предупреждения по мерам безопасностиПРЕДУПРЕЖДЕНИЕ ОСТОРОЖНОP E L I G R O Advertencias de SeguridadA D V E R T E N C I A P R E C A U C I Ó NF A R A SäkerhetsföreskrifterV A R N I N G V I K T I G TUPS Setup InstallationInspecting the Equipment ChapterC A U T I O N Installing the UPS Internal BatteriesTower Setup Figure 6. UPS Cabinet with Pedestals 5. Carefully position the cabinets upright see FigureFigure 7. Tower UPS with an EBM C A U T I O N EBM InstallationConnectors Figure 9. Typical EBM InstallationPlug-Receptacle UPS Installation Remote Emergency Power-off Installation W A R N I N G To install the REPO switchC A U T I O N W A R N I N G Hardwired UPS InstallationC A U T I O N Figure 12. Hardwired UPS Rear Panel Figure 13. UPS Terminal Block Table 1. UPS Wiring SpecificationsTightening Page INSTALLATION Operation Starting the UPS on BatteryTurning the UPS On ChapterTurning the UPS Off Initiating the Battery TestOperating Modes Transferring the UPS to Bypass ModePress the On button for approximately eight seconds to transfer the UPS to Bypass mode. TheFigure 15. Load Level Indicators Normal ModeFigure 16. Battery Capacity Indicators Battery ModeStandby Mode Bypass ModeTo reconfigure the UPS default settings ConfigurationChapter C A U T I O NTable 2. Configuration Mode LEDs and Options Figure 17. Using Configuration ModeBar Graph Indicators OptionUSB Port Chapter 6 CommunicationTable 3. Communication Port Pin Assignment DB-9 Communication PortX-Slot Cards COMMUNICATION UPS and Battery Care Chapter 7 UPS MaintenanceWhen to Replace Batteries Storing the UPS and BatteriesReplacing Batteries How to Replace Extended Battery ModulesW A R N I N G 6. Reinstall the joining brackets if removed in Step C A U T I O N How to Replace Internal BatteriesTesting New Batteries W A R N I N G Recycling the Used Battery or UPSC A U T I O N C A U T I O NChapter SpecificationsTable 4. Model List Table 5. Electrical InputSPECIFICATIONS Table 7. Environmental and SafetyTable 6. Electrical Output 0C to 40C 32F to 104FTable 9. Battery Table 8. Weights and DimensionsTable 10. Battery Runtimes in Minutes Extended Battery Module EBMSPECIFICATIONS Audible Alarms and UPS Conditions Chapter 9 TroubleshootingSilencing an Audible Alarm Alarm or Condition Table 11. Troubleshooting GuidePossible Cause ActionPossible Cause Alarm or ConditionAction 2 minutes 112-150% for up toAll other countries Call your local service representative Service and SupportUnited States 1-800-356-5737 or Canada1-800-461-9166 ext Two-Year Limited Warranty US and Canada Chapter 10 WarrantyWARRANTY Product repaired or replaced pursuant to terms of Limited Warranty Ten-Year Pro-Rated Limited Warranty US and Canada10 Years of Warranted Life WARRANTY Load Protection Guarantee US and Canada