Manuals / Printek / Computer Equipment / Printer

Printek PrintMaster 850 Series manual Control Codes and Escape Sequences Grouped by Function

Models: PrintMaster 850 Series FormsPro 4000se Series FormsMaster 8000se Series

1 166

Download 166 pages 48.2 Kb

Page 117

Genicom 3840 and 3410 ANSI Emulation

Control Codes and Escape Sequences Grouped by

Function

Communications

End of Text

EXT

If “ETX/ACK” is set to “On” in the serial interface setup menu, then receipt of an ETX causes the printer to transmit an ACK to the host computer.

Since the ETX may be a legal value within an escape sequence, it is the user's responsibility to ensure that an ETX used for data handshake is not sent within an escape sequence. The user must also ensure that the maximum block size or the number of blocks sent at one time does not exceed the input buffer size of the printer.

ETX/ACK handshake is available only with serial I/O.

Control code:	EXT
Hexadecimal:	03

Character Size

ANSI Oversized Font

ESC [(pv);(ph)<SP>B

Set Character Size

Sets the scaling of the oversize characters in percentage points. Pv is the vertical expansion, and Ph is the horizontal. The base font is a 10-point font. These settings are non-volatile, and should be set once before using the oversize font.

Differences from Genicom 3840 and 3410:

All Oversized Character features are supported. Expanded Mode is not supported in this printer.

Software Options That Affect Oversized Printing

Software Options are selected under the FormsPro, FormsMaster or PrintMaster series printer front panel Setup feature. These settings are non-volatile. One of these options affects Oversized Mode:

OPTIONS MENU	Possible Values
Top of Oversized	On / Off

When enabled, the vertical position on exiting oversized mode places the text baseline for subsequent printing so the top of the next character printed will align with the top of the oversized character cell. When disabled, the paper advances 1/8 inch on exiting oversized mode. Line/Character Spacing

ESC [(p1);(p2)<SP>G

111

Image 117

Printek PrintMaster 850 Series Control Codes and Escape Sequences Grouped by Function, Communications, Character Size

Contents

PrintMaster 850 Series FormsPro 4000se Series FormsMaster 8000se SeriesProgrammer’s Manual Printek, Inc 1517 Townline Road Benton Harbor, MISpecifications subject to change without notice ii INTRODUCTION TABLE OF CONTENTSANSI X3.64 EMULATION EPSON FX EMULATIONDEC LA120/210 EMULATION SIMPLE TTY EMULATIONPRINTEK EMULATION GENICOM 3840 AND 3410 ANSI EMULATION Page INTRODUCTION How to Use This ManualPrinter Model Descriptions and Key Features Selecting EmulationsIntroduction Changing Forms/Tractor Paths Page Introduction ANSI X3.64 EMULATIONESC f no numeric parametersANSI X3.64 Emulation Control Codes and Escape Sequences Grouped by Function CommunicationsEnd of Text Set Character and Line Spacing Character Size and Line Spacingline pitch 6 lpiHorizontal Position Character AttributesSelect Graphic Rendition Carriage ReturnAbsolute Horizontal Tab Vertical PositionRelative Horizontal Tab Line FeedESC K Partial Line DownPartial Line Up ESC LForm Length and Form Feed Horizontal and Vertical PositionNew Line Form FeedHorizontal Tab Horizontal TabsSet Horizontal Tab Stop Clear Horizontal Tab StopVertical Tab Vertical TabsSet Vertical Tab Stop ESC JANSI X3.64 Emulation Cancel Automatic Carriage Return Printer ControlsReset BellEmulations Select Software Interface nESC ESC n Control Codes and Escape Sequences Sorted Alphabetically Cancel Automatic Carriage ReturnSelect Automatic Carriage Return ANSI X3.64 Emulation Introduction EPSON FX EMULATIONControl Codes and Escape Sequences Grouped by Function Cancel LineCommunications Delete CharacterCancel MSB Control Character SizeSet MSB to Set MSB toESC P Select 10 CPISelect 12 CPI ESC MCancel Double-Wide Mode one line Cancel Condensed ModeControl code HexadecimalCancel Emphasized Mode Cancel Subscript and Superscript ModeCancel Double-Strike Mode Character AttributesUnderline Mode Cancel Italic ModeESC - n Select Italic ModeCharacter Sets Master Print Mode SelectSelect Draft or Letter Quality ESC k n Select FontFrance Select International Character SetGermany EnglandEnable Printing of High Symbols Line PitchDisable Printing of High Symbols Printing of Low SymbolsSet Line Spacing to n/216” Horizontal PositionESC 3 n Set Line Spacing to n/72”Form Length and Form Feed Vertical PositionBackspace Line FeedSet Form Length in Inches Set Form Length in LinesESC C NUL n Form FeedHorizontal Tab Horizontal TabsAbsolute Horizontal Tab Relative Horizontal TabSet Horizontal Tab Stops Vertical TabsVertical Tab Set Vertical Tab StopsVertical Margins Horizontal MarginsSet Left Margin ESC l nCancel Perforation Skip GraphicsSet Perforation Skip ESC O120 DPI Graphics 60 DPI GraphicsHigh Speed 120 DPI Graphics High Speed 240 DPI Graphicsm DPI Graphics Printer ControlsBell Control codeReset Forms and TractorsESC @ Load FormEmulations Select Software Interface nESC ESC n ESC * m n1 n2 data Sorted AlphabeticallyESC B n1 n2 ... nx NUL ESC D n1 n2 ... nx NULCancel Subscript and Superscript Mode ESC Y n1 n2 dataESC Z n1 n2 data Page Introduction IBM PROPRINTER EMULATIONControl Codes and Escape Sequences Grouped by Function Cancel LineCommunications End of TextSelect 10 CPI Character SizeSelect 12 CPI Select Condensed ModeSelect Double-Wide Mode one line Cancel Double-Wide Mode one lineESC SO Double-Wide ModeCharacter Attributes Cancel Subscript and Superscript Modecharacter width Select Subscript or Superscript ModeCancel Double-Strike Mode Cancel Emphasized ModeCharacter Sets ESC FPrint Single Character Line PitchESC n Print CharactersSet Line Spacing to 7/72” Horizontal PositionStart Line Spacing Set Line Spacing to n/216”Form Length and Form Feed Vertical PositionBackspace Line FeedSet Form Length in Inches Set Form Length in LinesESC C NUL n Form FeedVertical Tabs Horizontal TabsHorizontal Tab Set Horizontal Tab StopsReset Horizontal and Vertical Tab Stops Horizontal and Vertical TabsHorizontal Margins Vertical TabVertical Margins Cancel Perforation SkipSet Perforation Skip ESC O60 DPI Graphics Graphics120 DPI Graphics Printer ControlsBell Causes the printers bell to soundAutomatic Line Feed EmulationsSelect Software Interface n ESC ESC nIBM Proprinter Emulation ESC B n1 n2 ... nx NUL Control Codes and Escape Sequences Sorted AlphabeticallyESC D n1 n2 ... nx NUL ESC K n1 n2 dataSelect Double-Wide Mode one line IBM Proprinter EmulationPage Introduction DEC LA120/210 EMULATIONESC f no numeric parametersDEC LA120/210 Emulation Communications Control Codes and Escape Sequences Grouped by FunctionNull DeleteCharacter Size Set Character SpacingESC n w Character Sets Character AttributesSelect Graphic Rendition Select International Character SetFrance Line PitchGermany EnglandVertical Position Horizontal PositionCarriage Return BackspaceDEC LA120/210 Emulation Absolute Vertical TabRelative Vertical Tab Form Length and Form Feed Horizontal and Vertical PositionNew Line Set Form Length in LinesForm Feed Horizontal TabsHorizontal Tab Control codeESC g Clear Horizontal Tab StopESC 0 g ESC 2 gVertical Tab Vertical TabsControl code HexadecimalClear Vertical Tab Stop DEC LA120/210 EmulationESC 1 g Clear All Vertical Tab StopsHorizontal Margins Set Left and Right MarginESC n1 n2 s Vertical Margins Set Top and Bottom MarginsESC n1 n2 r Printer Controls Cancel Automatic Carriage ReturnBell Causes the printers bell to soundDEC LA120/210 Emulation GraphicsEmulations Select Software Interface nESC ESC n DEC LA120/210 Emulation Control Codes and Escape Sequences Sorted AlphabeticallyPage Introduction SIMPLE TTY EMULATIONCommunications Control Codes and Escape Sequences Grouped by FunctionHorizontal Position End of TextVertical Position Form length is the distance from the top of the form to the bottom of the form. A form feed will advance the paper to the top of the next form. Some programs do not send form feeds. Instead, they count line feeds, and send the appropriate number of line feeds to fill out the page. The usual rational is that the program is then in complete control of form length, and will work on any printer without requiring the correct form length to be set. However, the correct form length should always be set with the control panel setup. Even if the program does not use form feeds, the printer will automatically scroll a completed form up to the tear bar to be torn off. This automatic scroll is based upon form length. The easiest way to set form length is via the “Form Length” value in the forms menu so it will be correctly set for everyone using the formForm Length and Form Feed Line FeedVertical Tabs Horizontal TabsPrinter Controls Horizontal TabEmulations Select Software Interface nESC ESC n Simple TTY Emulation Control Codes and Escape Sequences Sorted AlphabeticallyIntroduction PRINTEK EMULATIONPrintek Emulation Communications Control Codes and Escape Sequences Grouped by FunctionEnd of Text Deselect PrinterSet Character Spacing Character SizeDouble-Wide Mode ESC W nEmphasized Mode Character AttributesDouble-Strike Mode Underline ModeSelect Font Character SetsPrint Single Character ESC \ nHorizontal Position Line PitchVertical Position Set Line Spacing to n/288”Reverse Line Feed Form Length and Form FeedSet Form Length in Lines Form FeedHorizontal Tab Horizontal TabsSet Horizontal Tab Stops ESC HT n1 n2 ... nx NULVertical Tabs Reset Horizontal and Vertical Tab StopsHorizontal and Vertical Tabs Vertical TabHorizontal Margins Set Left and Right MarginESC H n1 n2 Graphics Vertical MarginsSet Top and Bottom Margins ESC V n1 n2m DPI Graphics Printek Emulationm DPI Graphics Printer ControlsBell Causes the printers bell to soundAutomatic Modes ResetAuto Cut Cut FormForms and Tractors Load FormESC L n Emulations Select Software Interface nESC ESC n ESC # m n1 n2 data Control Codes and Escape Sequences Sorted AlphabeticallyESC * m n1 n2 data ESC HT n1 n2 ... nx NULIntroduction GENICOM 3840 AND 3410 ANSI EMULATIONESC f no numeric parametersGenicom 3840 and 3410 ANSI Emulation Communications Control Codes and Escape Sequences Grouped by FunctionCharacter Size End of TextFont And Print Modes Character SetSelects print modes and fonts Partial Line Down SubscriptSuperscript Printing Horizintal PositionSuperscript Printing Carriage ReturnESC pl Reset Auto CR ON LFHorizontal Position Backwards ESC pjLine Feed Vertical PositionESC D IndexVertical And Horiztonal Position Absolute Horiztonal TabVertical Position Backwards Horiztonal TabSet Horiztonal Tab Stop Vertical TabClear Tabs ESC PsgForms Setup Default ValuesForms Setup Margin SetupHexidemical GraphicsForm Feed Graphics ModeReset Printer ControlGraphics Density ESC p1qANSI Bar Codes Paper ShearPaper Shear ANSI Bar CodesIgnore Character Software Options That Affect BarcodesBarcode Options Barcode OptionsPaper Path Paper Pathp1 selects Select Software Interface n Emulationsn Software Interface ESC ESC nControl Codes and Escape Sequences Sorted Alphabetically Oversize Font / Graphic Size ModificationVertical and Horizontal Position Absolute Genicom 3840 and 3410 ANSI Emulation CONFIGURATION DOWNLOAD Configuration Download Remote Setup Line DefinitionsParallelInterface Remote Setup Example File HEX DUMP MODE Page Introduction PRINTING BASIC BAR CODESPrinting Basic Bar Codes Measurements in Bar Code Mode Bar Code SequencesEntering/Exiting Bar Code Mode BAR CODE SEQUENCEThe Bar Code Control Character Other Control CharactersPrinting Basic Bar Codes BNxccc...cG Bar Code DefinitionExample ExampleBNf12345G Printing Basic Bar CodesVariable Width Bar Code Definition ExampleBN9xddddccc...cG BNa12345G Printing Basic Bar CodesExample Bar Code HeightTwo Character Sequence Identifier for Range is 01 to 99 0.1 to 9.9 inchesTo print a bar code that is only 0.1 inch high H01BNe12345G ExampleExample ExampleAbsolute Horizontal Tab Relative Vertical TabJttd ExampleH02BNd01GT0200BNd02GT0400BNd03G Printing Basic Bar CodesBar Code Pass Terminator ExampleExample Mixing Bar Codes and Text ExampleExample Description of Supported Bar Code Types Page ASCII Control Code Definitions ASCII CHARACTER TABLESEpson FX Fast Draft Epson FX Draft Epson FX Letter Quality ASCII Character TablesPC Fast Draft PC Draft PC Letter Quality ASCII Character TablesEBCDIC Fast Draft EBCDIC Draft EBCDIC Letter Quality ASCII Character TablesASCII Character Tables Latin 2 Slavic Fast Draft Latin 2 Slavic DraftLatin 2 Slavic Letter Quality OCR A OCR B ML Euro ASCII Character TablesASCII Character Tables ML EuroASCII Character Tables Decimal to Octal to Hexadecimal Conversion TableHexASCII HexASCIIcleared unless reset from host PRINTER RESET CONDITIONScontrol character symbols text in an incomplete linePage GLOSSARY Glossary