Quadra-Fire VOYAGEUR-MBK K. Building A Fire, L. Fuel Reloading Instructions, VOYAGEUR Wood Insert

R

VOYAGEUR Wood Insert

K. Building A Fire

WARNING

Fire Risk.

Keep combustible materials, gasoline and other fl ammable vapors and liquids clear of appliance.

•Do NOT store fl ammable materials in the appliance’s vicinity.

•DO NOT USE GASOLINE, LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID OR SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS HEATER.

•Keep all such liquids well away from the heater while it is in use.

•Combustible materials may ignite.

Before lighting your fi rst fi re in the appliance:

1.Confi rm the baffl e and ceramic blanket are correctly positioned. They should be even with the front tube and resting on all tubes. See page 12.

2.Remove all labels from glass.

There are many ways to build a fi re. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling, which in turn ignites the slow-burning fi re- wood. Here is one method that works well:

1.Open the Burn Rate Air and Start-Up Air Controls fully.

2.Place several wads of crushed paper on the fi rebox fl oor. Heating the fl ue with slightly crumpled newspaper before adding kindling keeps smoke to a minimum.

3.Lay small dry sticks of kindling on top of the paper.

4.Make sure that no matches or other combustibles are in the immediate area of the appliance. Be sure the room is ventilated and the fl ue unobstructed.

5.Light the paper in the appliance. NEVER light or rekindle fi re with kerosene, gasoline, or charcoal lighter fl uid; the results can be fatal.

6.Once the kindling is burning quickly, add several full-length logs 3 to 4 inches (76 - 102mm) in diameter. Be careful not to smother the fi re. Stack the pieces of wood 1/2 to 1 inch apart (13-25mm); near enough to keep each other hot, but far enough away from each other to allow air fl ow between them.

7.Set the Burn Rate Air Control and activate the timer sys- tem (ACC).

8.When ready to reload, it is best to fully open both the Burn Rate Air and Start-up Air Controls before reloading.

L. Fuel Reloading Instructions

1.This appliance has a large door with an exceptional view of the fi re.

•Opens to about 90 degrees and has a built-in stop.

•Door opens 26 inches (660mm) which goes beyond the standard size hearth pad covering the fl oor in front of the appliance.

•May want to use a hearth rug in front of the hearth pad to protect the fl ooring from ash spillage and continuous cleaning of carpet, etc. See drawing on page 32.

2.Open door slowly so that ash or smoke does not exit appliance through opening.

•Check the level of the ash build-up. Remove ash if it reaches the top of the brick covers. Ash should not be spilling over the brick covers onto the ashlip.

•Any ash on the ashlip can be pressed into the door gasket and shorten the life of the gasket.

•If the ash is left to accumulate on the ashlip it can interfere with the door closing and/or falling out onto the hearth pad or beyond.

Check the ash level each time you reload.

NOTE:

•Build fi re on brick fi rebox fl oor only.

•Do NOT use grates or other methods to support fuel. It will adversely affect emissions.

CAUTION

Odors and vapors released during initial operation.

•Curing of high temperature paint.

•Open windows for air circulation.

Odors may be irritating to sensitive individuals.

•This livens up the coalbed and reduces excessive emis- sions (opacity/smoke).

•Large logs burn slowly, holding a fi re longer.

•Small logs burn fast and hot, giving quick heat.

November 22, 2011 7063-173D Page 13