Installing the Optional FAN, To Remove the Fan | Regency G36D

INSTALLATION

INSTALLING THE OPTIONAL FAN

120 Volt AC power is needed for the fan switch and blower. A three wire power cord is provided to be plugged into the receptacle.

Unit must be grounded at all times. Do not cut the ground terminal off under any circumstances.

1)Shut the power off.

2)Open the bottom louver door.

3)Slide the fan in towards the rear of the unit and slip it over the two mounting studs.

Ensure that the fan blades do not rub against the valve tubing.

Note: A 120 Volt AC power cord can be installed at rough-in stage so that the power is available. A three wire power cord can be used.

5)If the left spring was unhooked in step 3), hook it back into the bracket. Take care not to clip any wires.Attach the adhesive backed wire holder clip (Part #910-199) onto the stove base.

To Remove the Fan

1)Shut the power off.

2)Reverse the above instructions.

Note: The bearings are lubricated for life. Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

Optional: If you require extra space to slide the fan to the back, the left spring can be unhooked from the bracket.

4)Plug the fan to the receptacle as shown in the wiring diagram below.

UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace

33

Image 33

Regency G36D installation manual Installing the Optional FAN, To Remove the Fan, Open the bottom louver door

Contents

12/18/05 G36D Zero Clearance Direct Vent Gas Fireplace To the New Owner Information for MOBILE/MANUFACTURED Homes After First Sale Table of Contents Copy of Safety Decal for G36D-NG1 Safety Label300 Certified for/Certifiée pour Canada and U.S.A Installation Checklist InstallationImportant Message Save These Instructions Before YOU Start Diagram G36D Unit DimensionsLocating Your GAS Stove Manufactured Mobile Home Additional Requirements Clearances Mantel LEG ClearancesFraming Finishing Combustible Mantels Top Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing Strips Exterior Vent Area where terminal is not permitedLocations Vertical Termination Venting Secure Vent Rigid Pipe Venting Components List Alternate Rigid Pipe Venting Systems UltraGlow Direct Vent System Flex Rigid Pipe Venting Arrangements Horizontal Terminations Installation Rigid Pipe Venting Arrangements Vertical Terminations Installation Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Flex Liner Venting Arrangements Vertical Terminations Diagram 3a I g h t AchievedSnorkel Terminations Diagram Roof Pitch Firestop spacer must be installedCeiling to the position Continue to assemble pipe lengths Installation Procedures Offset ChartFor UltraGlow Direct Vent System Flex GAS Line Installation Pilot AdjustmentGAS Pipe Pressure Testing High Elevation LPG Conversion Kit Contains Installation of LPG Conversion KitQty DC Sparker Kit Contains Qty Sparker Ignitor Wire Ignitor WireGround Wire from Kit Piezo Ignitor Install the 1/2 bushing to the heat shield Heat ShieldChain LOG SET Installation 02-75 02-55 02-5202-53 02-51 02-54 Log indentation 5th Grate TabRear Grate Tab Front Brackets Place embers in these 3 locations On the burner tray Install ﬂ ush glass as per instructions in manual Standard Flush Door Flush LouversOptional Flush Trim Wall Switch Remote ControlThermostat Wire Table Wall Thermostat Do not cut the ground terminal off under any circumstances Wiring Diagram Installing the Optional FAN To Remove the FanOpen the bottom louver door Operating Instructions Maintenance Instructions Copy of the Lighting Plate InstructionsNormal Operating Sounds of GAS Appliances Maintenance Removing Valve Installing Valve G36D Main Assembly Pilot Assembly Gasket Parts List G36D Flush Front Assembly UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace Warranty ConditionsExclusions Register your UltraGlow online at