Factory Default, CTL Maintenance | Ricoh 406460 manual

Service Program Mode

Fax Maintenance

V34 Settings

Equalizer

Redialing

First TX Speed

Symbol Rate

These selectors set the equalizer's training level to be applied if training fails due to poor line connection.

[Automatic (Default)/ 4 Points/ 16 Points]

Resend when a communication error occurs. [Disabled (Default)/ Not Disabled]

Sets the first transmission speed choice, before fallback. [2400 Bps/ 4800 Bps/ 7200 Bps/ 9600 Bps

/12000 Bps/ 14400 Bps/ 16800 Bps/ 19200 Bps/

21600 Bps/ 24000 Bps/ 26400 Bps/ 28800 Bps/

31200 Bps/ 33600 Bps (Default)]

This setting limits the transmission speed range in V.34 mode by masking the desired symbol rate(s).

[Not Used (Default)/ 3429 Sym/Sec

/3200 Sym/Sec/ 3000 Sym/Sec

/2800 Sym/Sec/ 2400 Sym/Sec]

5

Factory Default

Factory Default

Not Execute

Execute

Does not execute anything. Returns to an upper level.

Resets all the settings to factory default.

•Clears/ resets the contents of the controller board memory (all data programmed by the user, log data) to factory default.

After executing, initial setup menu starts after power-on.

CTL Maintenance

	CTL Maintenance		PDL Mode		ON = "PDL Settings" is shown (Default)
	CTL Maintenance		PDL Mode		OFF = "PDL Settings" is hidden
					OFF = "PDL Settings" is hidden

103

Image 105

Ricoh 406460 service manual Factory Default, CTL Maintenance

Contents

November Model RN-MF1 Machine Codes M016/M017Page Important Safety Notices Safety Notices WARNING Laser Safety Trademarks Symbols, Abbreviations and Trademarks Table of Contents Page System Maintenance Reference Troubleshooting Page Product Information Component Layout Machine Overview Paper Path Drive Layout Machine Configuration Product Information Environment Installation Requirements Machine Level Power Requirements Installation Procedure Installation PM Intervals PM PartsYield Counter Counter Reset Before You Start Replacement and Adjustment Special Tools Front Cover Exterior Covers Left Cover Exterior Covers Replacement and Adjustment Rear Cover Right Cover Top Cover When installing the top cover ADF Unit ADF ADF Feed Unit Original Tray ADF Front Cover ADF Separation Pad ADF Cover ADF Rear Cover ADF Motor Original Set Sensor ADF Cover Open Sensor ADF Feed Sensor ADF Drive Board Operation Panel Scanner Unit Scanner Top Cover Scanner Carriage Unit Scanner Unit Exposure Lamp Lamp Stabilizer Board When reinstalling the exposure lamp Scanner Motor Scanner Unit Laser Unit Laser Unit Polygon Mirror Motor Replacement and Adjustment After installing a new paper feed roller Paper Feed and ExitPaper Feed Roller Friction Pad When reinstalling the friction pad follow this orderPaper End Sensor By-pass Feed Roller Paper Feed and Exit By-Pass Feed Roller Friction Pad Paper Feed Clutch By-pass Feed Sensor Harness guide plate B x Relay Clutch Registration ClutchToner End Sensor Relay Sensor Paper Exit Sensor Registration Roller and Sensor Inverter Sensor Exit roller base B x Paper Feed and Exit Registration sensor a After installing a new transfer roller Paper TransferTransfer Roller Fusing Unit Fusing Fusing Reinstallation After installing a new fusing unitThermostat Thermistor Fusing Lamp Hot Roller When reinstall the fusing lamp Hot Roller Stripper Pawls Pressure Roller Fusing Motors Main MotorDuplex Motor For M017 Duplex motor a x 2, x Electrical Components Layout of PC BoardsECB Engine Controller Board Electrical Components Controller Board Eeprom FCU USB Host Board PSU Electrical Components Rear low cover a x Electrical Components Charge Terminal Case Others Cooling FanSpeaker Quenching Lamp Registration Adjustment Image AdjustmentUser Adjustment Service Adjustment Replacement and Adjustment Service Program Mode Maintenance Mode MenuOverview Print Reports Engine Maintenance Service Program Mode Engine Maintenance Brand ID Fuser SC Reset Bypass Tray Priority Paper Feed Roller Pages Engine Maintenance Paper Buckle Amount Fusing Unit Temperature Sheets Toner end To 255 Sheet/step Scan Maintenance Scan Maintenance Fax Maintenance RX Settings Silence Detection Time TX Settings Backtone To the Line DFU CTL Maintenance Factory Default Fax Service Test Menu Entering the Fax Service Test MenuFax Test Fax Test To Print the Configuration Page/ Maintenance Configuration and Maintenance Total Counter Other Types of ReportsTotal Counter Application Counters Firmware Updating ProcedureChecking the Machine Firmware Version Updating the Controller Firmware Firmware Updating Updating the Engine Firmware Above updating program should appear on the screen FW Update Tool Messages Updating the Boot Loader FirmwareFW Update Tool Messages Information Message for USB update Messages Comment Action FW Update Tool Messages Error Is in power-on stage 116 Fusing related SCs Service Call ConditionsSC 2xx Laser Optics Error Summary Troubleshooting SC 5xx Motor and Fusing Error SC 4xx Image Transfer and Transfer Error Issue this SC code and cannot be operated 121 122 SC 6xx Communication and Other Error Image Problems Test Page Print ProcedureTest Page Printing Test Pattern Printing Test Pattern Print Procedure Surface of the drum Dark lines in halftone areas at 75mm Intervals Jam Jam Sensor LayoutPaper Jam Original Jam Jam Message List Sensor duplex feed tray 130 Timer Settings Energy SaveEnergy Saver Modes Recommendation Return to Stand-by ModeEnergy Saver Mode1 Energy Saver Mode2 Paper Save Combine modeEffectiveness of Duplex/Combine Function Duplex Paper Saved 136 Model RN-MF1 Machine Codes M016/M017 Appendices Page Appendix Specifications Page Custom size Appendix Specifications ADF RET Printer APS/ AMS Copier Fax Scanner MH/MR/MMR Auto Answer Rings Default 3 rings Input Tray Type Size Supported Paper Sizes Executive Appendix Specifications Service Menu Appendix SP Mode Tables Appendix Troubleshooting Guide Error Messages List Error Messages Error Messages Basic error code structure Fax Error Code MMR Error Type Error Description Error Code Error code table Error Messages EOR/ERR/DCN