Error Messages | Ricoh 406460 instruction

				Error Messages


	Error Type		Error Description	Error Code

			TX T1 Time Out	xxxx31

			V8 negotiation Fail	xxxx32

			Retry Out	xxxx40

			Too many FTT	xxxx41

			Too many CRP	xxxx42

			T2 Time Out	xxxx43
	Comm. Error	1. Phase-B Error
	Comm. Error	1. Phase-B Error	DCN received	xxxx44
			DCN received	xxxx44

			Command Rec Error	xxxx45

			Resp Rec Error	xxxx46

			Invalid Command/Response	xxxx47
			RX	xxxx47
			RX

			Remoter No RX capability	xxxx48

			T1 time out after EOM	xxxx49

			T2 Time Out	xxxx50

		2. Phase-C Error	Image Data not ready	xxxx51

			Phase-C Time Out	xxxx52

3

21

Image 161

Ricoh 406460 service manual Error Messages

Contents

November Model RN-MF1 Machine Codes M016/M017Page Important Safety Notices Safety Notices WARNING Laser Safety Trademarks Symbols, Abbreviations and Trademarks Table of Contents Page System Maintenance Reference Troubleshooting Page Product Information Component Layout Machine Overview Paper Path Drive Layout Machine Configuration Product Information Environment Installation Requirements Machine Level Power Requirements Installation Procedure Installation Yield Counter PM IntervalsPM Parts Counter Reset Before You Start Replacement and Adjustment Special Tools Front Cover Exterior Covers Left Cover Exterior Covers Replacement and Adjustment Rear Cover Right Cover Top Cover When installing the top cover ADF Unit ADF ADF Feed Unit Original Tray ADF Front Cover ADF Separation Pad ADF Cover ADF Rear Cover ADF Motor Original Set Sensor ADF Cover Open Sensor ADF Feed Sensor ADF Drive Board Operation Panel Scanner Unit Scanner Top Cover Scanner Carriage Unit Scanner Unit Exposure Lamp Lamp Stabilizer Board When reinstalling the exposure lamp Scanner Motor Scanner Unit Laser Unit Laser Unit Polygon Mirror Motor Replacement and Adjustment Paper Feed Roller After installing a new paper feed rollerPaper Feed and Exit Friction Pad When reinstalling the friction pad follow this orderPaper End Sensor By-pass Feed Roller Paper Feed and Exit By-Pass Feed Roller Friction Pad Paper Feed Clutch By-pass Feed Sensor Harness guide plate B x Toner End Sensor Relay ClutchRegistration Clutch Relay Sensor Paper Exit Sensor Registration Roller and Sensor Inverter Sensor Exit roller base B x Paper Feed and Exit Registration sensor a Transfer Roller After installing a new transfer rollerPaper Transfer Fusing Unit Fusing Fusing Thermostat ReinstallationAfter installing a new fusing unit Thermistor Fusing Lamp Hot Roller When reinstall the fusing lamp Hot Roller Stripper Pawls Pressure Roller Fusing Duplex Motor For M017 MotorsMain Motor Duplex motor a x 2, x ECB Engine Controller Board Electrical ComponentsLayout of PC Boards Electrical Components Controller Board Eeprom FCU USB Host Board PSU Electrical Components Rear low cover a x Electrical Components Charge Terminal Case Speaker OthersCooling Fan Quenching Lamp Registration Adjustment Image AdjustmentUser Adjustment Service Adjustment Replacement and Adjustment Overview Service Program ModeMaintenance Mode Menu Print Reports Engine Maintenance Service Program Mode Engine Maintenance Brand ID Fuser SC Reset Bypass Tray Priority Paper Feed Roller Pages Engine Maintenance Paper Buckle Amount Fusing Unit Temperature Sheets Toner end To 255 Sheet/step Scan Maintenance Scan Maintenance Fax Maintenance RX Settings Silence Detection Time TX Settings Backtone To the Line DFU CTL Maintenance Factory Default Fax Test Fax Service Test MenuEntering the Fax Service Test Menu Fax Test To Print the Configuration Page/ Maintenance Configuration and Maintenance Total Counter Other Types of ReportsTotal Counter Application Counters Firmware Updating ProcedureChecking the Machine Firmware Version Updating the Controller Firmware Firmware Updating Updating the Engine Firmware Above updating program should appear on the screen FW Update Tool Messages Updating the Boot Loader FirmwareFW Update Tool Messages Information Message for USB update Messages Comment Action FW Update Tool Messages Error Is in power-on stage 116 Fusing related SCs Service Call ConditionsSC 2xx Laser Optics Error Summary Troubleshooting SC 5xx Motor and Fusing Error SC 4xx Image Transfer and Transfer Error Issue this SC code and cannot be operated 121 122 SC 6xx Communication and Other Error Test Page Printing Image ProblemsTest Page Print Procedure Test Pattern Printing Test Pattern Print Procedure Surface of the drum Dark lines in halftone areas at 75mm Intervals Paper Jam JamJam Sensor Layout Original Jam Jam Message List Sensor duplex feed tray 130 Energy Saver Modes Timer SettingsEnergy Save Recommendation Return to Stand-by ModeEnergy Saver Mode1 Energy Saver Mode2 Paper Save Combine modeEffectiveness of Duplex/Combine Function Duplex Paper Saved 136 Model RN-MF1 Machine Codes M016/M017 Appendices Page Appendix Specifications Page Custom size Appendix Specifications ADF RET Printer APS/ AMS Copier Fax Scanner MH/MR/MMR Auto Answer Rings Default 3 rings Input Tray Type Size Supported Paper Sizes Executive Appendix Specifications Service Menu Appendix SP Mode Tables Appendix Troubleshooting Guide Error Messages List Error Messages Error Messages Basic error code structure Fax Error Code MMR Error Type Error Description Error Code Error code table Error Messages EOR/ERR/DCN