Symbols, Abbreviations and Trademarks | Ricoh 406460 manual

Symbols, Abbreviations and Trademarks

This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations are as follows:

SEF

LEF

See or Refer to

Clip ring

Screw

Connector

Clamp

E-ring

Short Edge Feed

Long Edge Feed

Trademarks

Microsoft®, Windows®, and MS-DOS®are registered trademarks of Microsoft Corporation in the United States and /or other countries.

PostScript® is a registered trademark of Adobe Systems, Incorporated. PCL® is a registered trademark of Hewlett-Packard Company. Ethernet® is a registered trademark of Xerox Corporation.

PowerPC® is a registered trademark of International Business Machines Corporation.

Other product names used herein are for identification purposes only and may be trademarks of their respective companies. We disclaim any and all rights involved with those marks.

3

Image 5

Ricoh 406460 service manual Symbols, Abbreviations and Trademarks

Contents

November Model RN-MF1 Machine Codes M016/M017Page Important Safety Notices Safety Notices WARNING Laser Safety Trademarks Symbols, Abbreviations and Trademarks Table of Contents Page System Maintenance Reference Troubleshooting Page Product Information Component Layout Machine Overview Paper Path Drive Layout Machine Configuration Product Information Environment Installation Requirements Machine Level Power Requirements Installation Procedure Installation Yield Counter PM IntervalsPM Parts Counter Reset Before You Start Replacement and Adjustment Special Tools Front Cover Exterior Covers Left Cover Exterior Covers Replacement and Adjustment Rear Cover Right Cover Top Cover When installing the top cover ADF Unit ADF ADF Feed Unit Original Tray ADF Front Cover ADF Separation Pad ADF Cover ADF Rear Cover ADF Motor Original Set Sensor ADF Cover Open Sensor ADF Feed Sensor ADF Drive Board Operation Panel Scanner Unit Scanner Top Cover Scanner Carriage Unit Scanner Unit Exposure Lamp Lamp Stabilizer Board When reinstalling the exposure lamp Scanner Motor Scanner Unit Laser Unit Laser Unit Polygon Mirror Motor Replacement and Adjustment Paper Feed Roller After installing a new paper feed rollerPaper Feed and Exit Friction Pad When reinstalling the friction pad follow this orderPaper End Sensor By-pass Feed Roller Paper Feed and Exit By-Pass Feed Roller Friction Pad Paper Feed Clutch By-pass Feed Sensor Harness guide plate B x Toner End Sensor Relay ClutchRegistration Clutch Relay Sensor Paper Exit Sensor Registration Roller and Sensor Inverter Sensor Exit roller base B x Paper Feed and Exit Registration sensor a Transfer Roller After installing a new transfer rollerPaper Transfer Fusing Unit Fusing Fusing Thermostat ReinstallationAfter installing a new fusing unit Thermistor Fusing Lamp Hot Roller When reinstall the fusing lamp Hot Roller Stripper Pawls Pressure Roller Fusing Duplex Motor For M017 MotorsMain Motor Duplex motor a x 2, x ECB Engine Controller Board Electrical ComponentsLayout of PC Boards Electrical Components Controller Board Eeprom FCU USB Host Board PSU Electrical Components Rear low cover a x Electrical Components Charge Terminal Case Speaker OthersCooling Fan Quenching Lamp Registration Adjustment Image AdjustmentUser Adjustment Service Adjustment Replacement and Adjustment Overview Service Program ModeMaintenance Mode Menu Print Reports Engine Maintenance Service Program Mode Engine Maintenance Brand ID Fuser SC Reset Bypass Tray Priority Paper Feed Roller Pages Engine Maintenance Paper Buckle Amount Fusing Unit Temperature Sheets Toner end To 255 Sheet/step Scan Maintenance Scan Maintenance Fax Maintenance RX Settings Silence Detection Time TX Settings Backtone To the Line DFU CTL Maintenance Factory Default Fax Test Fax Service Test MenuEntering the Fax Service Test Menu Fax Test To Print the Configuration Page/ Maintenance Configuration and Maintenance Total Counter Other Types of ReportsTotal Counter Application Counters Firmware Updating ProcedureChecking the Machine Firmware Version Updating the Controller Firmware Firmware Updating Updating the Engine Firmware Above updating program should appear on the screen FW Update Tool Messages Updating the Boot Loader FirmwareFW Update Tool Messages Information Message for USB update Messages Comment Action FW Update Tool Messages Error Is in power-on stage 116 Fusing related SCs Service Call ConditionsSC 2xx Laser Optics Error Summary Troubleshooting SC 5xx Motor and Fusing Error SC 4xx Image Transfer and Transfer Error Issue this SC code and cannot be operated 121 122 SC 6xx Communication and Other Error Test Page Printing Image ProblemsTest Page Print Procedure Test Pattern Printing Test Pattern Print Procedure Surface of the drum Dark lines in halftone areas at 75mm Intervals Paper Jam JamJam Sensor Layout Original Jam Jam Message List Sensor duplex feed tray 130 Energy Saver Modes Timer SettingsEnergy Save Recommendation Return to Stand-by ModeEnergy Saver Mode1 Energy Saver Mode2 Paper Save Combine modeEffectiveness of Duplex/Combine Function Duplex Paper Saved 136 Model RN-MF1 Machine Codes M016/M017 Appendices Page Appendix Specifications Page Custom size Appendix Specifications ADF RET Printer APS/ AMS Copier Fax Scanner MH/MR/MMR Auto Answer Rings Default 3 rings Input Tray Type Size Supported Paper Sizes Executive Appendix Specifications Service Menu Appendix SP Mode Tables Appendix Troubleshooting Guide Error Messages List Error Messages Error Messages Basic error code structure Fax Error Code MMR Error Type Error Description Error Code Error code table Error Messages EOR/ERR/DCN