Hot Roller, When reinstall the fusing lamp | Ricoh 406460 instruction

Fusing

When reinstall the fusing lamp

4

The flat terminal [A] must be placed on the right side of the fusing unit (fusing cable side).

Hot Roller

1. Fusing lamp ( p.68)

2. Brackets [A] ( x 2)

69

Image 71

Ricoh 406460 service manual Hot Roller, When reinstall the fusing lamp

Contents

November Model RN-MF1 Machine Codes M016/M017Page Important Safety Notices Safety Notices WARNING Laser Safety Trademarks Symbols, Abbreviations and Trademarks Table of Contents Page System Maintenance Reference Troubleshooting Page Product Information Component Layout Machine Overview Paper Path Drive Layout Machine Configuration Product Information Environment Installation Requirements Machine Level Power Requirements Installation Procedure Installation Yield Counter PM IntervalsPM Parts Counter Reset Before You Start Replacement and Adjustment Special Tools Front Cover Exterior Covers Left Cover Exterior Covers Replacement and Adjustment Rear Cover Right Cover Top Cover When installing the top cover ADF Unit ADF ADF Feed Unit Original Tray ADF Front Cover ADF Separation Pad ADF Cover ADF Rear Cover ADF Motor Original Set Sensor ADF Cover Open Sensor ADF Feed Sensor ADF Drive Board Operation Panel Scanner Unit Scanner Top Cover Scanner Carriage Unit Scanner Unit Exposure Lamp Lamp Stabilizer Board When reinstalling the exposure lamp Scanner Motor Scanner Unit Laser Unit Laser Unit Polygon Mirror Motor Replacement and Adjustment Paper Feed Roller After installing a new paper feed rollerPaper Feed and Exit By-pass Feed Roller When reinstalling the friction pad follow this orderFriction Pad Paper End Sensor Paper Feed and Exit By-Pass Feed Roller Friction Pad Paper Feed Clutch By-pass Feed Sensor Harness guide plate B x Toner End Sensor Relay ClutchRegistration Clutch Relay Sensor Paper Exit Sensor Registration Roller and Sensor Inverter Sensor Exit roller base B x Paper Feed and Exit Registration sensor a Transfer Roller After installing a new transfer rollerPaper Transfer Fusing Unit Fusing Fusing Thermostat ReinstallationAfter installing a new fusing unit Thermistor Fusing Lamp Hot Roller When reinstall the fusing lamp Hot Roller Stripper Pawls Pressure Roller Fusing Duplex Motor For M017 MotorsMain Motor Duplex motor a x 2, x ECB Engine Controller Board Electrical ComponentsLayout of PC Boards Electrical Components Controller Board Eeprom FCU USB Host Board PSU Electrical Components Rear low cover a x Electrical Components Charge Terminal Case Speaker OthersCooling Fan Quenching Lamp Service Adjustment Image AdjustmentRegistration Adjustment User Adjustment Replacement and Adjustment Overview Service Program ModeMaintenance Mode Menu Print Reports Engine Maintenance Service Program Mode Engine Maintenance Brand ID Fuser SC Reset Bypass Tray Priority Paper Feed Roller Pages Engine Maintenance Paper Buckle Amount Fusing Unit Temperature Sheets Toner end To 255 Sheet/step Scan Maintenance Scan Maintenance Fax Maintenance RX Settings Silence Detection Time TX Settings Backtone To the Line DFU CTL Maintenance Factory Default Fax Test Fax Service Test MenuEntering the Fax Service Test Menu Fax Test To Print the Configuration Page/ Maintenance Configuration and Maintenance Application Counters Other Types of ReportsTotal Counter Total Counter Updating the Controller Firmware ProcedureFirmware Updating Checking the Machine Firmware Version Firmware Updating Updating the Engine Firmware Above updating program should appear on the screen Message for USB update Updating the Boot Loader FirmwareFW Update Tool Messages FW Update Tool Messages Information Messages Comment Action FW Update Tool Messages Error Is in power-on stage 116 Summary Service Call ConditionsFusing related SCs SC 2xx Laser Optics Error Troubleshooting SC 5xx Motor and Fusing Error SC 4xx Image Transfer and Transfer Error Issue this SC code and cannot be operated 121 122 SC 6xx Communication and Other Error Test Page Printing Image ProblemsTest Page Print Procedure Test Pattern Printing Test Pattern Print Procedure Surface of the drum Dark lines in halftone areas at 75mm Intervals Paper Jam JamJam Sensor Layout Original Jam Jam Message List Sensor duplex feed tray 130 Energy Saver Modes Timer SettingsEnergy Save Energy Saver Mode2 Return to Stand-by ModeRecommendation Energy Saver Mode1 Duplex Combine modePaper Save Effectiveness of Duplex/Combine Function Paper Saved 136 Model RN-MF1 Machine Codes M016/M017 Appendices Page Appendix Specifications Page Custom size Appendix Specifications ADF RET Printer APS/ AMS Copier Fax Scanner MH/MR/MMR Auto Answer Rings Default 3 rings Input Tray Type Size Supported Paper Sizes Executive Appendix Specifications Service Menu Appendix SP Mode Tables Appendix Troubleshooting Guide Error Messages List Error Messages Error Messages Basic error code structure Fax Error Code MMR Error Type Error Description Error Code Error code table Error Messages EOR/ERR/DCN