1822-I Pipe and Bolt Threading Machine

8.Move die head to UP position.

9.Release foot switch and remove your foot from the housing.

Removing Pipe From The Threading Machine

1.Turn the control switch to the OPEN position. Depress foot switch and machine will release the pipe.

2.Release foot switch and turn control switch to the OFF position.

WARNING Never reach inside chuck cover while ma- chine is connected to a power source. Fingers can be crushed.

3.Slide the workpiece out of the Threading Machine, keeping a firm grip on the workpiece as it clears the Threading Machine.

WARNING To avoid injury from falling parts or equip- ment tip-overs when handling long workpieces, make sure that the end farthest from the Threading Machine is supported prior to removal.

4.Clean up any oil spills or splatter on the ground sur- rounding the Threading Machine.

Installing Dies In Self-Opening Die Head (Right Hand Only)

The No. 815A Self-Opening Die Head (Figure 10) for right hand threads requires four sets of dies to thread pipe ranging from 1/8″ through 2″. One set of dies is required for each of the following pipe size ranges: (1/8″), (1/4″ and 3/8″), (1/2″ and 3/4″) and (1″ through 2″). Bolt threading re- quires a separate set of dies for each bolt size.

NOTE! High speed dies are recommended for thread- ing 1″ to 2″ pipe at 45 RPM.

1.Place self-opening die head on bench in vertical po- sition.

2.Make sure trigger assembly is released.

3.Loosen clamp lever approximately six full turns.

4.Pull lock screw out of slot under size bar so that roll pin in lock screw will bypass slot. Position size bar so that index line on lock screw is aligned with the end of REMOVE DIES position.

5.Lay die head down with numbers up.

6.Remove dies from die head.

7.Insert new dies to mark on side of dies. Numbers 1 through 4 on the dies must match numbers on the die head.

8.Move throwout lever back to lock in dies.

9.With head in vertical position, rotate cam plate until roll pin on lock screw can be positioned in slot under size bar. In this position dies will lock in die head. Make sure roll pin points toward end of size bar marked RE-

MOVE DIES.

10.Adjust die head size bar until index line on lock screw is aligned with proper size mark on size bar.

Roll Pin

Size Bar

 

Index Line

 

Lock Screw

 

 

Clamp

 

Lever

Throwout

 

Lever

 

 

Trigger

 

Assembly

Figure 11 – Universal Self-Opening Die Head

11.Tighten clamp lever.

12.If oversize or undersize threads are required, set the index line in direction of OVER or UNDER size mark on size bar.

NOTE! When left hand threading the UNDER/OVER positions are reversed.

Installing Dies In Quick-Opening Die Head (Right and Left Hand)

The No. 811A Universal Die Head (Figure 11) for right hand threads requires four sets of dies to thread pipe ranging from 1/8″ through 2″. One set of dies is required for each of the following pipe size ranges: (1/8″), (1/4″ and 3/8″), (1/2″ and 3/4″) and (1″ through 2″). Bolt threading re- quires a separate set of dies for each bolt size. No bolt dies are available for left hand universal die heads.

12

Ridge Tool Company

Page 13 Page 15
Page 14
Image 14
RIDGID 1822-I Removing Pipe From The Threading Machine, Installing Dies In Self-Opening Die Head Right Hand Only, Trigger
Page 13 Page 15

1822-I specifications

The RIDGID 1822-I is a powerful and versatile compact pipe threading machine that is widely recognized for its reliability and innovative design. This electric threading machine is specifically engineered for both professional and DIY users, ensuring high productivity in pipe fitting and fabrication tasks.

At the core of its engineering, the RIDGID 1822-I features a robust motor that delivers high torque, allowing for efficient threading of a variety of pipe sizes up to 2 inches in diameter. This machine is equipped with a quick-release pipe clamp that securely holds the workpiece in place, providing enhanced stability and safety during operations. The user-friendly controls enable seamless operation with minimal setup time, making it an ideal choice for contractors and plumbing professionals.

One of the standout technologies integrated into the RIDGID 1822-I is its automatic shut-off feature that enhances safety while prolonging the lifespan of the machine. It also boasts an adjustable threading stop, allowing operators to maintain consistent thread lengths and ensuring precision in their work. This machine is compact in design, enabling easy portability and storage, which is especially beneficial for jobs in confined spaces or on construction sites.

The RIDGID 1822-I is constructed using durable materials and comes with a sturdy frame that minimizes vibration, significantly reducing user fatigue during extended use. Additionally, it features an integrated oil reservoir that simplifies the process of threading pipes, ensuring proper lubrication and ensuring smoother cuts.

Another characteristic that sets the RIDGID 1822-I apart is its versatility. It is compatible with various RIDGID threading dies and accessories, allowing for customization based on the specific requirements of each job. Furthermore, the machine's exceptional threading speed leads to increased efficiency, enabling users to complete projects more quickly without compromising on quality.

In conclusion, the RIDGID 1822-I is an indispensable tool for professionals looking for a reliable, efficient, and versatile pipe threading solution. Its combination of advanced features, durability, and user-friendly design make it a top choice for those in the plumbing and construction industries, as well as for DIY enthusiasts seeking a dependable machine for their pipe threading needs. With the RIDGID 1822-I, users can achieve high-quality results with ease and confidence.
Top Page Image Contents