43
Creating a Patch
[F1 (WG PRM)]
Parameter marked with a “
★
” can be controlled using specified MIDI messages
(Matrix Control, p. 49)
Parameter Group [F2 (WG)] Modifying Waveforms/Pitch/Pitch Envelope
Parameter Value Explanation
Wave Group INT, EXP,
SAMP,
MSAM
Group for the waveform that is to be the basis of the tone
INT:
Waveforms stored in internal
EXP:
Waveform stored in a Wave Expansion Board (SRX series) installed in EXP slots
SAMP:
Sample waveforms
MSAM:
Multisample waveforms
Wave Bank PRST, USER,
CARD
When the Wave Group is SAMP: PRST, USER, CARD
When the Wave Group is MSAM: USER, CARD
Wave No. L (Mono)
Wave No. R
----, 1–1228 Basic waveform for a tone (The upper limit will depend on the wave group.)
When in monaural mode, only the left side (L) is specified. When in stereo, the right side (R) is also
specified.
If you want to select a left/right pair of Waves, select the left (L) Wave number, and then hold down
[SHIFT] and press [F4 (STEREO)] to add a check mark (
✔
); the right (R) (Wave) will be recalled.
* When using a multisample in stereo, you must specify the same number for L and R.
Wave Gain -6, 0, +6, +12 Gain (amplification) of the waveform
The value changes in 6 dB (decibel) steps—an increase of 6 dB doubles the waveform’s gain.
*If you intend to use the Booster to distort the waveform’s sound, set this parameter to its maximum value (p. 39).
Wave Tempo Sync OFF, ON When you wish to synchronize a Phrase Loop to the clock (tempo), set this to “ON.”
* This is valid only when a separately sold wave expansion board is installed, and a waveform that indicates a
tempo (BPM) is selected as the sample for a tone.
If a waveform from a wave expansion board is selected for the tone, turning the Wave Tempo Sync pa-
rameter “ON” will cause pitch-related settings (p. 44) and FXM-related settings (p. 43) to be ignored.
• If a sample is selected for a tone, you must first set the BPM (tempo) parameter of the sample.
• If a sample is selected for a tone, Wave Tempo Sync will require twice the normal number of voices.
• When this parameter is set to “ON,” set the Tone Delay Time parameter (p. 51) to “0.”
Parameter Value Explanation
FXM Switch OFF, ON This sets whether FXM will be used (ON) or not (OFF).
FXM Color 1–4 How FXM will perform frequency modulation
Higher settings result in a grainier sound, while lower settings result in a more metallic sound.
FXM Depth
★
0–16 Depth of the modulation produced by FXM

Phrase Loop

Phrase loop refers to the repeated playback of a phrase that’s
been pulled out of a song (e.g., by using a sampler). One
technique involving the use of Phrase Loops is the excerpting of
a Phrase from a pre-existing song in a certain genre, for example
dance music, and then creating a new song with that Phrase
used as the basic motif. This is referred to as “Break Beats.”

Realtime Time Stretch

If the wave group is “SAMP” or “MSAM,” and the Wave
Tempo Sync parameter is turned “ON,” you can vary the
playback speed of the waveform without affecting the pitch.

FXM

FXM (Frequency Cross Modulation) uses a specified waveform
to apply frequency modulation to the currently selected
waveform, creating complex overtones. This is useful for
creating dramatic sounds or sound effects.
Fantom-Xa_e.book 43ページ ２００４年１０月２２日　金曜日　午後２時３分