Russound CAV6.6-S2 ZONE SETUP (ZonSu)

61

INSTALLER

INSTALLATION MENU

Source Select Command (cont’d)

e. All Other Selections: Procedure advances to DEVICE CODE (step 3)

3. DEVICE CODE – Source component code for IR control.

(DevCd)

4. KEY FUNCTION – Select a function (Play, Enter, etc.).

(KeyFn)

5. SAVE CHANGES? – Select “yes” to save the changes.

(Save?)

# OF SOURCES (#Srcs)

At this field it is necessary to enter the number of sources used in the CAV6.6 system (1 to 6). This

limits the sources displayed on the keypad in the normal running mode when the source button is

pressed, but also limits source selections in the configuration menus.

See Source Setup Menu on

Page 55 and Source Select Command & # Of Sources - Flow Char t on page 71

ZONE SETUP (ZonSu)

NOTE: This procedure should be performed using the keypad installed in the zone to be configured.

See Installation Menu on Page 55 and Zone Setup - Flow Chart on page 72

Zone Setup allows the installer to adjust properties of the UNO Keypad controlled CAV6.6 zone. This

series of menus allows the system’s zones to be configured for these proper ties:

ZON VOL TRIM (ZonVT) SYSON ENABLE (SysOn) PARTY ENABLE (PtyEn) MAS-

TER ENABL (MstEn) PAGE ENABLE (PagEn) PAGE VOLUME (PagVl)

1. ZON VOL TRIM - This feature allows the installer to adjust the output volume to

(ZonVT) each zone. -16 dB (lowest) to 0 dB (max)(default).

2. SYSON ENABLE - This feature is either disabled or enabled. If disabled (default), an

(SysOn) All On command activated from another zone will not turn on the

disabled zone. If enabled, an All On command activated from

another zone will turn on the enabled zone.

3. PARTY ENABLE - This feature is either disabled or enabled. If disabled, Party Mode

(PtyEn) activation from another zone will not affect the disabled zone. If

enabled (default), the zone will participate with Par ty Mode.

4. MASTER ENABLE - This feature is either disabled or enabled. If disabled, the zone

(MstEn) cannot host a master keypad during Party Mode. If enabled

(default), the zone has the option of hosting the Master keypad.

Contents

Main Precautions: IMPORTANT SAFEGUARDS Page TABLE OF CONTENTS Page PRODUCT INTRODUCTION Page Page UNO-S2 Keypad-Front Panel Optional UNO-S1 Keypad-Front Panel UNO-LRC1 Remote Control CAV6.6 Controller UNO-S2 Keypad UNO-S2 Keypad Button Functions UNO-S2 User Menu - Setting Preferences Optional UNO-S1 Keypad Button Functions Optional UNO-S1 User Menu - Setting Preferences INSTALLER SECTION GETTING STARTED WIRING INSTRUCTIONS Page CAV6.6 Controller-Front Panel Page CAV6.6 Controller-Rear Panel UNO-S2 Keypad-Front Panel UNO-S2 Keypad-Rear Panel Keypad Location www.russound.com. UNO-S2 Keypad Connections IR Receiver Connection UNO System Keypad Port Connection (See Sample System Configuration 3, page 89) Source Audio/Video Input Connections Source Audio/Video Loop Output Connections Speaker Connections ACC IR Connection Zone Audio (to Amp) and Video Outputs A-BUS Ready Sub-zone Connection Page Page Page Page RNET Link In and Link Out - Multiple Controllers RNET Link In and Link Out - RNET-enabled Components RS-232 Interface www.russound.com. Programming Center Keypad Por t Connection UNO-S2 Keypad Diagnostics Menu UNO-S2 Keypad Firmware Update Procedure CAV6.6 Firmware Update Procedure System requirements for PC Power Tool: PC POWER TOOL OVERVIEW PC Power Tool Programming INITIAL INSTALL TEST PROGRAMMING System Programming Overview PROGRAMMING System Programming Overview (contd) Page Page Page Go to previous menu / procedure / feature. Enter menu / begin procedure / show current feature setting. SOURCE SETUP (SrcSu) BASIC SETUP (BasSu) See Basic Setup - Flow Chart on page 67 Basic Setup (contd.) KEY CONFIG (KeyCf) See Key Config. - Flow Chart on page 68 Key Config (contd.) SOURCE NAMES (SrcNm) See Source Setup Menu on Page 55 and Source Names/Vol Trim - Flow Chart on page 69 Disc SRC VOL TRIM (SrcVT) See Source Setup Menu on Page 55 and Source Names/Vol Trim - Flow Chart on page 69 Numeric IR (contd) Enter Numeric IR (contd) SRC SEL CMD (SrcSC) See Source Setup Menu on Page 55 and Source Select Command & # Of Sources - Flow Chart on page 71 Source Select Command (contd) # OF SOURCES (#Srcs) ZONE SETUP (ZonSu) See Installation Menu on Page 55 and Zone Setup - Flow Chart on page 72 CTRLR SETUP (CtlId) Zone Setup (contd) See Installation Menu on Page 55 and Controller Setup - Flow Chart on page 73 WARNING: This procedure returns the controller to its original settings - use with discretion. Power Management (contd) See Installation Menu on Page 55 and Power Management - Flow Chart on page 74 LEARN IR (LrnIR) Power Management (contd) See Installation Menu on Page 55 and Learn IR - Flow Chart on page 75 MACRO EDITOR (MacEd) Learn IR (contd) See Installation Menu on Page 55 and Macro Editor - Flow Chart on page 76 Macro Editor (contd) SYSTEM INFO (SInfo) See Installation Menu on Page 55 and System Info - Flow Chart on page 77 Page Page Page Page Page Page Page Page Page Page Page REFERENCE SECTION Device Codes for TVs: Device Codes for Cable: Device Codes for Video Acc: Device Codes for SAT/DSS: Device Codes for VCRs: Device Codes for Laser Disc Players: Device Codes for DVD Players: Device Codes for Tuner/Amp: Device Codes for Amp and Misc. Audio: Device Codes for CD Players: Device Codes for Home Contr ol: Page SOURCE NAMES SAMPLE SYSTEM CONFIGURATION 1 Six Zones and Six Sources Page SAMPLE SYSTEM CONFIGURATION 2 Integrate Multiple CAV6.6s Page SAMPLE SYSTEM CONFIGURATION 3 Zone Keypad Expansion Page SAMPLE SYSTEM CONFIGURATION 4 A-BUS Ready Sub-Zone Addition Page SAMPLE SYSTEM CONFIGURATION 5 Additional Amplification Page SAMPLE SYSTEM CONFIGURATION 6 Home Theater Page Page TV (HDTV) Page CABLE Page VIDEO ACC Page SAT/DSS Page VCR Page LASER DISC Page DVD Page RECEIVER Page AMP/MISC AUDIO Page CD Page HOME CONTROL TECHNICAL SPECIFICATION WARRANTY & REPAIR