Samsung RF31FMEDBSR, RF31FMESBSR, RF31FMEDBBC user manual For Ice/water model Only, Saver, Reset

USING THE CONTROL PANEL

RF31FMED**

(For Ice/water model Only )

1	4
2	5
3	6

10	9
7	8

( 1 )	Touching this button turns Energy Saver
Energy
	mode on and off. When you turn Energy
Saver
	Saver on, the Energy Saver icon lights.
	Turn Energy Saver off and the icon goes
	off. The Energy Saver function’s factory
	setting is “ON”. If condensation or water
	drops appear on the doors, turn the
	Energy Saver mode off.

(2 ) The Freezer button serves two purposes:

Freezer	- To set the Freezer to your desired
(Hold 3	temperature.
sec for	- To turn the power freeze function on
Power	and off.
Freeze)	1) To set the Freezer temperature
	Touch the Freezer button to set the
	Freezer to your desired temperature. You
	can set the temperature between 5 °F
	(-15 °C) and -8 °F (-23 °C).
	2) Power Freeze function
	Touch and hold this button for 3 seconds
	to decrease the time needed to freeze
	products in the Freezer.
	It can be helpful if you need to quickly
	freeze easily spoiled items or if the
	temperature in the freezer has warmed
	dramatically (For example, if the door was
	left open).
	When you use this function the energy
	consumption of the refrigerator will
	increase.
	Remember to turn it off when you don’t
	need it and return the freezer to your
	original temperature setting. If you need to
	freeze large amount of food stuff, activate
	Power Freeze function at least 20 hours
	before.

(3 ) The Alarm button serves two purposes:

Alarm	- To turn the door open alarm on and off
(Hold 3	- To reset the water filter life indicator.
sec for	1) Door Alarm Function
Filter	If the door alarm is set to On, an alarm
Reset	beeps if any refrigerator door is left open
	for more than three minutes. The beeping
	stops when you close the door. The door
	alarm function is pre-set to On in the
	factory. You can turn it off by pressing and
	then releasing the Alarm button. You can
	turn it back on in the same fashion. The
	icon lights up when the function is on.
	When the Door Alarm function is on and
	the alarm sound is triggered, the Door
	Alarm Icon will blink while the alarm
	sounds.
	2) Water Filter Life Indicator Function
	After you replace the water filter, touch
	and hold this button for 3 seconds to
	reset the water filter life indicator. When
	you reset the water filter life indicator, the
	Filter icon on the panel turns Off. The
	Filter icon will turn red to let you know it
	is time to change the water filter after six
	months (about 300 gallons). Some areas
	have large amounts of lime in their water,
	which causes the water filter to clog more
	quickly. If this is the case in your area,
	you will have to change the filter more
	frequently than every six months.
( 4 )	Lighting button serves two purposes:
Lighting
(Hold 3	- To turn the dispenser light on and off
sec for ºC	- To switch the temperature units
↔ ºF)	between ºC and ºF
	1) Light Function
	Touching the Lighting button turns on
	the Dispenser LED lamp in continuous
	mode so that it stays on continuously.
	The button also lights up. If you want the
	Dispenser lamp to come on only when
	some one uses the dispenser, press the
	Lighting button to turn the continuous
	mode off.
	2) To switch the temperature units
	between ºC and ºF,
	Touch and hold this button for 3 seconds
	to select the temperature display you
	want.
	Each time you press and hold the button,
	the ºC and ºF temperature modes
	alternate and the ºC or ºF icon lights up,
	indicating your selection.

24_ operating

DA68-02894A-09.indb 24 2013. 12. 3. ￿￿ 8:45