Manuals / Brands / Computer Equipment / Projector / Samsung / Computer Equipment / Projector

Samsung SP-H700, SP-H500, SP-H710 Restoring the Factory Default Settings

1 84

Download 84 pages, 4.75 Mb

Restoring the Factory Default Settings

Used to restore setting values to factory defaults.

Setup Restoring the Factory Default Settings

2, 3, 4

Select

2, 3, 4

…/†/œ/√

EXIT

NOTE

User settings including

Edit Name and Custom

Picture will be reset.

Press the MENU button.

The main menu is displayed.

Press the ▲or ▼button to move to Setup.

The Setup menu is displayed.

Press the button.

Press the EXIT button to exit the menu.

Press the ▲or ▼button to move to Factory

Default, then press the button.

Press the œor √button to move to OK, then

press the button.

Setting values are returned to factory defaults.

Setup

Install : Front-Floor √

Light Setting : Theater √

V-Keystone √

Test Pattern √

PC √

Factory Default √

Information √

Move Enter Return

Factory Default

Move

Back to Factory Default setting?

Cancel

Enter Return

Contents

Main Connections and Source Setup Preparation Preparation Table of Contents Setup Picture Adjustment Page Preparation Features and Design Optical engine adopting advanced DLP technology User adjustments Vivid colors Minimized fan noise and light leakage Caution on Lamp Use and Replacement Preparation Caution on Lamp Use Projector Lamp Caution on Lamp Replacement Page Page Front/Upper Side Front/Upper Side and Accessories Accessories : Turned On : Flashing : Turned Off Indicator Information Clearing Indicator Problems Rear Side and Cables Rear Side Cables Remote Control Buttons Operating the Remote Control Operating Move/Select Button Inserting Batteries into Remote Control Allowable range & angle of receiving the remote control signal Using Remote Control in Dark Place (LIGHT) Installation and Turning On To Install the Projector Installing Projector in Front of the Screen Installing Projector on Backside of Screen Turning On Projector Zoom and Focus Adjustment Using the Zoom Knob and the Focus Ring Leveling with Adjustable Feet Using Adjustable Feet Using the Lens Shift Dial Using the Lens Shift Dial This projector is designed to show images optimally on a 80 to 150 inch sized screen. Y X Screen Size and Projection Distance Check the following before reading this manual. SP-H700/SP-H710 Screen Size and Projection Distance SP-H500 This projector is designed to show images optimally on a 80 to 150 inch sized screen. X Y Page Check the following Before Connecting Before Connections Connecting to VCR/Camcorder/Cable Box Connecting to DVD 1 Connecting to the Digital TV Receiver Connections and Source Setup Press the desired source button (COMP.1/ COMP.2/ S-VIDEO/COMPOSITE/ PC/DVI). The Source List menu is displayed. The Input menu is displayed. Setting up the External Input Source You can select a device connected to the projector to display. Press the button to select Input. Press the button to select Source List. Press the or button to move to desired input Naming the External Connections You can select and set up the type of device you want to connect to the projector. Setup is switched to the selected device. The Edit Name menu is displayed. The Input menu is displayed. Page Picture Adjustment Selecting Picture Mode Picture Adjustment Press the P.MODEbutton. Custom Settings of the Picture Picture Adjustment Custom Picture Menu Press the CUSTOM button. Press the or button to move to desired item, Changing the Color Standard Color Standard Press the or button to move to Color Standard, then press the button. Press the or button to adjust the selected item. Selecting and Adjusting Color Temperature Picture Adjustment 7 Press the or buttons to select an option then Color Temperature Menu Gamma Correction The Custom Picture menu is displayed. Gamma is used to improve the picture quality with color balance. Refer to page 30 for information on Gamma Mode1, 2, and 3. Press the or button to move to Gamma, Saving Custom Picture Settings The Save menu is displayed. 7 The Custom Picture menu is displayed. 7 Setting up DNIe DNIe Mode Press the or button to move to DNIe, then Off DNle Mode Off Demo DNle On/Off Picture Comparison Mode On DNle Mode On Picture Adjustment Selecting Picture Size Press the P.SIZEbutton. Each press of the button, picture size is switched to Full, Zoom1, Zoom2 and 4:3. Press the or button to move to Picture Size, Page Picture Adjustment Screen Position Adjustment Press the or button to move to Position, Press the , , , or buttons to adjust the position. Film Mode Supports enhanced screen quality for films of 24 frames. Picture Adjustment Press the or button to move to Film Mode, Overscan Picture Adjustment Press the or button to move to Overscan, Page Page Flipping/Reversing the Projected Image Setup Install Menu Press the INSTALL button. Light Setting Light Setting Mode Press the or button to move to Light Setting, then press the button. Correcting Vertical Keystone Setup Press the or button to adjust. Press the V.KEYSTONEbutton. Press the or button to move to V-Keystone, Test Patterns Setup Test Pattern Menu Press the or button to move to Test Pattern, pattern, then press the button. Restoring the Factory Default Settings Used to restore setting values to factory defaults. Setting values are returned to factory defaults. Setup /// Information You can check external source signals, picture setup, PC picture adjustment and lamp use time. OK Setup Press the INFO button. Page Page Setting the Language You can select the language used for the menu screen. Setup is switched to the selected language. The Language is selected. Menu Option Setting the Menu Position Menu Option Setting the Menu Translucency You can set the translucency of menu. Press the button. Menu Option Press the or button to move to Menu Translucency, then press the button. Setting Up the Menu Display Time You can set the display time of the menu. Setup is switched to the selected time. Press the button. Menu Option Page Connecting to PC Before Connecting to PC Check the following before connecting the projector to a PC. Display modes supported by this projector The table complies to IBM/VESA requirements and is based on analog signal input. Refer to "Rear Side and Cables" on page 10 for cables used for connection. Setting up the PC Environment Connecting to PC Connecting to PC Connecting to PC Viewing the PC Screen Using PC Video Cable or DVI Cable Connecting to PC Connecting to PC CAUTION DVI-D cable does not support analog RGB signals. VESA Plug & Play PC Video Cable (15-pin signal) DVI-D Automatic Picture Adjustment Used to adjust frequency and phase of PC screen automatically. The Auto Adjustment is selected. Connecting to PC Before adjusting! Frequency Adjustment Fine Tuning with the Phase Adjustment Connecting to PC Zooming the Screen Connecting to PC Reset the PC Page Troubleshooting Installation and Connection Menu and Remote Control Before Contacting Service Personnel Troubleshooting Screen and External Source Page Page Storage and Maintenance Other Information Cleaning the Projector and Lens Cleaning the Inside of the Projector Purchasing Optional Parts Optional Parts Structure of Screen Menu Buttons used for Screen Menu Select Composite/S-Video/Component Input Mode Page Structure of Screen Menu Lamp Replacement Other Information 123 5 4 Cautions on Lamp Replacement RS-232C Connection and Control Connecting the Projector to a PC Other Information Structure for Variables (8 bytes) Communication Format (Complies with the RS232C Standard) Commands Other Information : Range is 50 ~ 50, use the Boolean Complementary for negative values. Specifications Other Information Remote Control Specifications